Best Spiral Flute Adjusting Reamer

2/0 Taper Pin Reamer Kit

Straight Shank with 3-Equal-Flats to Fit 3/8'' or 1/2" Chuck.
Include size: 3/8" (fit 3/8'' shank chuck), 1/2", 5/8", 3/4" (fit 1/2'' shank chuck).
Straight shank with stop collar to prevent the reamer running through the hole.

High-speed steel tools are good for most general purpose applications, offering a combination of hardness and toughness for wear resistance.
Available in uncoated (bright) and black oxide finish.
Round shanks allow use with a wide variety of toolholding systems.
Square shank allows hand (straight and spiral flute) reamers to be held in a tap wrench or vise, depending on whether the reamer of the part is rotated.

When the diameter wears down to the low limit, it may be expanded oversize, reground to size and recleared. The expansion screw should never be loosened in an attempt to use the reamer for a size smaller than that to which the tool was originally finish ground. These reamers are inteded to be used for 1 specific diameter, not multiple diameters..
1 1/2 " flute length, Partial Flute Length Carbide.
3/4 " shank diameter, For Reaming abrasive material.
This is an expansion reamer NOT an adjustable reamer. It can be expanded only and reground..

When the diameter wears down to the low limit, it may be expanded oversize, reground to size and recleared. The expansion screw should never be loosened in an attempt to use the reamer for a size smaller than that to which the tool was originally finish ground. These reamers are inteded to be used for 1 specific diameter, not multiple diameters..
1 1/2 " flute length, Partial Flute Length Carbide.
Morse taper shank #3, For Reaming Abrasive Material.
This is an expansion reamer NOT an adjustable reamer. It can be expanded only and reground..

When the diameter wears down to the low limit, it may be expanded oversize, reground to size and recleared. The expansion screw should never be loosened in an attempt to use the reamer for a size smaller than that to which the tool was originally finish ground. These reamers are inteded to be used for 1 specific diameter, not multiple diameters..
1 1/2 " flute length, Partial Flute Length Carbide.
Morse taper shank #2, For Reaming Abrasive Material.
This is an expansion reamer NOT an adjustable reamer. It can be expanded only and reground..

When the diameter wears down to the low limit, it may be expanded oversize, reground to size and recleared. The expansion screw should never be loosened in an attempt to use the reamer for a size smaller than that to which the tool was originally finish ground. These reamers are inteded to be used for 1 specific diameter, not multiple diameters..
1 3/8 " flute length, Partial Flute Length Carbide.
Morse taper shank #2, For Reaming Abrasive Material.
This is an expansion reamer NOT an adjustable reamer. It can be expanded only and reground..

When the diameter wears down to the low limit, it may be expanded oversize, reground to size and recleared. The expansion screw should never be loosened in an attempt to use the reamer for a size smaller than that to which the tool was originally finish ground. These reamers are inteded to be used for 1 specific diameter, not multiple diameters..
1 3/4 " flute length, Partial Flute Length Carbide.
1" shank diameter, For Reaming abrasive material.
This is an expansion reamer NOT an adjustable reamer. It can be expanded only and reground..

When the diameter wears down to the low limit, it may be expanded oversize, reground to size and recleared. The expansion screw should never be loosened in an attempt to use the reamer for a size smaller than that to which the tool was originally finish ground. These reamers are inteded to be used for 1 specific diameter, not multiple diameters..
2" flute length, Partial Flute Length Carbide.
Morse taper shank #4, For Reaming Abrasive Material.
This is an expansion reamer NOT an adjustable reamer. It can be expanded only and reground..

When the diameter wears down to the low limit, it may be expanded oversize, reground to size and recleared. The expansion screw should never be loosened in an attempt to use the reamer for a size smaller than that to which the tool was originally finish ground. These reamers are inteded to be used for 1 specific diameter, not multiple diameters..
1 7/8 " flute length, Partial Flute Length Carbide.
Morse taper shank #4, For Reaming Abrasive Material.
This is an expansion reamer NOT an adjustable reamer. It can be expanded only and reground..

The reamer range is 15/32 inch to 1-1/2 inch..
Product includes 11Pcs high speed adjustable hand reamers H4-H14..
The adjustable reamer is made of HSS(high speed steel) with good hardness and toughness..
Adjustable reamer is straight flute with straight handle..
The reamer is suitable for drilling machines and other machine..

Premium Material: The material is low alloy steel with high hardenability and low hardenability. The reamer has the characteristics of high wear resistance, less severe cutting and less deformation..
Hand Reamer: Reamer for reaming holes have been drilled after processing (or reaming) on the workpiece, mainly to improve the precision of the hole, reducing its surface roughness, is finishing and semi-finishing tool for the hole..
Straight Flute Tool: 6 Flutes & Straight Shank. Allows chips to collect in the flutes when cutting, well suited for most applications in shallow cuts..
Application Object: Installed in the lathe for cutting of metal tools. Straight flute hand reamers is used in ferrous metals and most nonferrous metals. Designed for accurate reaming in aluminum, cast iron, copper, magnesium alloy, plastic, wood, etc..
Application: Good for general purpose applications, offering combination of hardness and toughness for wear resistance. Features just the base substrate without any additional treatment or coatings, suitable for wide ranges of applications..