Stepper peristaltic Pump 24V high Flow Kamoer KPHM400 lab Liquid dosing Pump 400ml/min Variable Speed

  • KPHM series peristaltic pump, the new design makes the pump tube is well fixed and prevents the pump tube from moving during operation. It is also a low-cost large flow peristaltic pump with stepper motor..
  • Motor: Stepper motor,Voltage: 24V,Current: 0.3A,Flow rate: 400ml/min,Speed: 400rpm,Net weight: 304g,Roller: 3 rotors,Working Temperature: 0-40℃,Humidity: <80%,Pump head material: Nylon.
  • Pump tube material:PharMed BPT.Very good resistance to general chemicals, as well as excellent resistance to acids, alkalis and oxides..
  • No pollution,low pulsation.The gearbox drives the pump tube to work, and the pump tube is not easy to slip.The liquid only touches the pump tube, not the pump body..
  • Application:Experimental Research,Experimental Monitoring,Inkjet.Printing,Aquarium,Smart Home,Aviation Operation.
Check Stock

Longruner 5X Geared Stepper Motor 28byj 48 Uln2003 5v Stepper Motor Uln2003 Driver Board with ArduinoIDE (no Wire)

  • 5pcs Stepper motor and driver board compatible with 2560 1280 DSP ARM PIC AVR STM32 Raspberry Pi..
  • Stepper motor with a standard interface. A, B, C, D four-phase LED indicates the status of the stepper motor work..
  • Motor diameter: 1.1 inches.Wire length:9.05 inchs. Stepping angle: 5.625 x 1/64.Reduction ratio: 1/6.Drive Module Board Size:1.26 inchsX1.38inchs. Cable length: about 20cm /8-inch..
  • Great packing in a box : 5 set Uln2003 Stepper Motor + Driver Board..
Check Stock

diymore 5-Set DC12V 28BYJ-48 Stepper Motor with ULN2003 Drive Boards Blue(12V)

  • Stepper motor driver board with ULN2003..
  • A, B, C, D four-phase LED indicates the status of the stepper motor work..
  • Stepper motor with a standard interface, when used directly pluggable..
Check Stock

Planetary Gearbox Nema 23 Ratio 10:1 Gear Head Speed Reducer 1/4\ Input fit for 6.35mm Shaft Stepper Motor CNC Router Lathe DIY(10:1)

  • ★Input shaft hole is 1/4" that can match the 6.35mm shaft motor (without key). The output shaft diameter is 14mm.
  • ★The gear head has Nema 23 Input & output flange,suitable for flange 57mm stepper motor and other motors which can completely match the installation size ..
  • ★Rated speed is 3000RPM, 10:1 gear ratio ,the rated holding torque is 15N.m and the Max. holding torque is 25N.m.
  • ★4pcs screws provide for installation , small size gearbox , very convenient for the machine which has limited space for a gearbox..
  • ★Widely used on kinds of machine , lathe ,engraving machine etc..
Check Stock

Kiro&Seeu 2PCS DC5V 28BYJ-48 Geared Stepper Motor with ULN2003 Drive Boards Blue for Arduino (5V)

  • Stepper motor driver board with ULN2003..
  • A, B, C, D four-phase LED indicates the status of the stepper motor work..
  • Stepper motor with a standard interface, when used directly pluggable..
Check Stock

Linear Guide Slide Table, Mini Linear Stage Actuator, Small Linear Guide Rail CNC Ball Screw Motion Rail, with 2-Phase 4-Wire Stepper Motor, for DIY Small Sliders 20mm

  • Can be used in DIY small sliders, projects, measuring equipment, laser printers..
  • This product is miniature 2‑phase 4‑wire stepper motor with planetary gearbox reducer..
  • Planetary gearbox reducer adopts all metal structure, strong and durable, has a long service life..
  • Drive accurate diagonal lines to move the metal slider up and down, and the bracket is basically made of metal structure..
  • The driving voltage of the motor is 5-9V/200-600mA, the higher the voltage, the greater the force and the greater the heat..
Check Stock

60:1 Worm Gear Speed Reducer Reduction Gearbox Ratio Gear Box

  • Input Bore Size: 11mm Input Flange Model: NEMA23.
  • Output Bore Size: 14mm Application: Matched with Servo/Stepper Motor.
Check Stock

MINARIK MM23001C 0-90/0-180V-DC 1/4-2HP 5A AMP DC MOTOR DRIVE D506404

  • Motor Driver: 9V-42V DC power supply, H bridge bipolar constant phase flow drive. The maximum 4.0A of the eight kinds of output current..
  • Motor Driver: Energy-saving semi-automatic current lock function, built-in temperature protection and over current protection.The largest 32 subdivision of the 6 models are optional..
  • Package: TB6600 stepper motor driver + nema 17 stepper motor + mounting bracket + inner hexagon spanner + M3/M4 screws.
  • Strive for 100% service satisfactory, any question or problem please do not hesitate to contact us, we are always happy to help..
Check Stock

X27 168 Stepper Motor Kit, Instrument Cluster Gauge Repair Kit Compatible with 03-06 GM Chevy Silverado (35 Led Light Bulbs+7 Motors+Soldering Iron+Solder Sucker+Remove Tool+Flux Rosin Core Solder)

  • COMPATIBILITY - Instrument Cluster Gauge Stepper Motor Repair Kit Compatible with 03-06 GM Chevy Silverados Tahoes Yukons. The instrument cluster repair kit perfectly replacement for the XC5-168, X15-168 ,X25-168 and X27-168 that are in your gauge cluster for 2003 2004 2005 2006 GM GMC Chevy Silverado Trailblazer. Came in your vehicles, Please check whether this X27 168 Stepper Motor Kit fits your vehicles before buying.
  • APPLIED TO - The latest stepper motor, direct replacement for the older and faulty stepper motors. Used for the repair of the speedometer,tachometer,oil pressure gauge,transmission temperature gauge, battery voltage gauge, water temperature gauge or fuel gauge. These gauge cluster repair kit have been redesigned for maximum reliability and quiet operation. Insert the needle as long as you pay attention to the zero pressure can be pressed, remember not to edge pressure.
  • FIX GLITCHES - High-quality motors that meet strict international quality standards to fix common problems caused by stepper motor of your vehicles: gauges dead, chatter, sticking, false / jumpy / inaccurate readings, pegged out to the left or right of the dial, ratchet up or down, sticky needle movement, erratic gauge movement etc. Each gauge of your instrument cluster ....
Check Stock

Dr.Roc Compatible Instrument Cluster Gauge Stepper Motor Repair Kit Fits X27 168 03 to 06 with 7 Stepper Motors Soldering Iron Solder Sucker Chevy Silverado GM GMC

  • The latest generation,Premium stepper motor,quiet operation and reliability,Perfectly Replace for the older and faulty XC5-168( XC5168 ), X15-168( X15168 ) ,X25-168 ( X25168 ) and X27-168 ( X27168 , X27.168 , X27 168 ) stepper motor that came in your vehicles,Use the tool on the upper left corner to check whether this product fits your vehicles.
  • Stepper motor is used for repairing guage cluster,including speedometer,tachometer,oil pressure gauge,transmission temperature gauge, battery voltage gauge, water temperature gauge or fuel gauge.
  • Solve the common problems of your vehicle such as, gauges cluster dead,chatter,sticking,false/jumpy/inaccurate readings,pegged out to the left or right of the dial, ratchet up or down,sticky needle movement,erratic gauge movement etc.
  • Each gauge of your instrument cluster need one stepper motor.Since one stepper motor went out,and it will result all other stepper motors go out soon. Checking the quantity of stepper motors for your vehicle to decide to buy the 6 or 7 one.It is easy to use for upgraded adjustable soldering iron,but you’d better to search the instructions Video on Internet first,which is very helpful..
  • The premium instrument cluster repair kit is compatible with Silverado,Suburban,Traiblazer,Tahoe,Avalanc....
Check Stock

Creality 3D Printer 42-40 Stepper Motor 2 Phases 1A 1.8 Degrees 0.4 N.M Stepper Motor for 3D Printer Extruder Compatible with E-axis of CR-10 Series and Ender-3 Series

  • Compatible: The stepper motor 42-40 applies to Eixe series Ender and CR-10 (e.g. Ender-3 / Ender 3 Pro / CR 10 / CR 10S etc.)..
  • 1.8 degree step angle, 0.4 N.M holding torque, with 0.8 A rated current per phase..
  • High Quality Stepping Motor: The high quality motor with low power, smooth speed, stable performance, low noise and no loss during operation, which....
  • Low noise: stepper motor with low noise level and efficient heat dissipation has the large torque and high precision without losing step..
  • What You Get: 1x 42-40 Stepper Motor (Note: This item does not include a connection cable or screws.).
Check Stock

G-Hubble Ender 3 Dual Z Axis Upgrade Kit with Lead Screw Stepper Motor 3D Printer Accessories Parts for Creality Ender 3/Ender 3 Pro/Ender 3 V2/Voxelab Aquila

  • Motor Driver: 9V-42V DC power supply, H bridge bipolar constant phase flow drive. The maximum 4.0A of the eight kinds of output current..
  • Motor Driver: Energy-saving semi-automatic current lock function, built-in temperature protection and over current protection.The largest 32....
  • Package: TB6600 stepper motor driver + nema 17 stepper motor + mounting bracket + inner hexagon spanner + M3/M4 screws.
  • Strive for 100% service satisfactory, any question or problem please do not hesitate to contact us, we are always happy to help..
Check Stock

Nema17 42 Stepper Motor 40mm 64oz.in 45Ncm 1.7A 1.8 Degree 2phase with 1M 4-pin Cable& Connector for 3D Printer Hobby CNC Router Engraving Milling Machine 17HS4401J

  • It with 1.8°± 5%step angle (200 steps/revolution) Phase:2.
  • Product Dimensions: 1.6 x 1.5 x 1.6 inches.
Check Stock