Categories

Best Tap And Die Set For Stainless Steel

uxcell Tap and Die and Drill Bit Set M14 x 2 Left Hand Thread Milling Tap and Round Die 12mm Cobalt High Speed Steel Twist Drill Bit

  • Compatibility: M14 x 2 metric tap and die set are suitable for making or repairing male and female threads. They are both left hand thread, durable, and with clear threads, good for general purpose applications..
  • Thread Tap: Straight flute design, downward chip removal. Process through holes in maintenance and repair work. For tapping aluminum, die steel, stainless steel, bronze, hard plastics etc.. Use with tapping oil to get higher quality threads and more durable taps..
  • Round Die: The round die features good abrasion resistance. Used with die wrench (not included). The fastening screws in the middle of the wrench should be inserted into the slot of the die and tightened. Suitable lubricating oil should be added to the cutting edge..
  • 12mm Drill Bit: Spiral chip space design for fast and clean chip removal. M35 cobalt high speed steel tool features high hardness (HRC65-66) and high red hardness, high wear resistance. Specially used for drilling stainless steel..
  • Tips: Recommended feed rate: general steel: 6-15m/min.
  • cast iron: 8-10m/min. The torque caused by too fast feed speed is too large, which can easily cause the tap to break..
Check Stock

uxcell Tap and Die and Drill Bit Set M12 x 1.75 Left Hand Thread Milling Tap and Round Die 10.2mm Cobalt High Speed Steel Twist Drill Bit

  • Compatibility: M12 x 1.75 metric tap and die set are suitable for making or repairing male and female threads. They are both left hand thread, durable, and with clear threads, good for general purpose applications..
  • Thread Tap: Straight flute design, downward chip removal. Process through holes in maintenance and repair work. For tapping aluminum, die steel, stainless steel, bronze, hard plastics etc.. Use with tapping oil to get higher quality threads and more durable taps..
  • Round Die: The round die features good abrasion resistance. Used with die wrench (not included). The fastening screws in the middle of the wrench should be inserted into the slot of the die and tightened. Suitable lubricating oil should be added to the cutting edge..
  • 10.2mm Drill Bit: Spiral chip space design for fast and clean chip removal. M35 cobalt high speed steel tool features high hardness (HRC65-66) and high red hardness, high wear resistance. Specially used for drilling stainless steel..
  • Tips: Recommended feed rate: general steel: 6-15m/min.
  • cast iron: 8-10m/min. The torque caused by too fast feed speed is too large, which can easily cause the tap to break..
Check Stock

Aceteel 1/2\-28 UNEF HSS Tap And Die Set, 1/2 x 28 UNEF Machine Thread Tap And Round Thread Die Right Hand

  • ...you easily eliminate the flaws on the threads.
  • Fine craftsmanship: the polished thread tap kit is made with advanced technology and craftsmanship, which can fit nicely with screws.
  • In addition, after being treated with a corrosion-resistant satin finish, the thread cutting friction is smaller and the surface becomes stainless steel, making it to be more bright and textured.
  • Size information: the package comes with 9 x metric taps and 9 x metric dies in different specifications, namely, M3 (0.5 mm)/ M4 (0.7 mm)/ M5 (0.8 mm)/ M6 (1 mm)/ M7 (1 mm)/ M8 (1.25 mm)/ M9 (1.25 mm)/ M10 (1.5 mm)/ M12 (1.75 mm).
  • Adjustable tap wrench handle measures about 19.5 cm/ 7-11/16 inch long, suitable for M3 to M12 (1/16 to 1/2 inch), and the die wrench handle is about 20 cm/ 7-7/8 inch long, suitable for M25 (1 inch).
  • Suitable for beginners and skilled people: this tooth opener kit is the nice assistant for craftsmen no matter if you are a novice or a skilled worker, which is very suitable for cleaning low-carbon steel or aluminum products in construction, automobile maintenance and factories, largely improving work efficiency and having strong practicability.
Check Stock

GMTOOLS 110PCS Tap and Die Set Metric Size Standard Threading Tool Set M2-M18 with Adjustable Handles Accessories and Storage Case Tap & Die Set for Cutting External and Internal Threads

  • [High-Quality Materials]: This metric tap set is made of high-quality hardened alloy steel, improving product hardness, wear-resistance, and increasing product service life, durable and superior strength..
  • [Excellent Performance]: Suitable for re-threading fasteners and fastener holes, cutting or updating internal and external threads. Fully ground & high-precision tap is sharp for tapping and chip removing operation, running smoothly and efficiently..
  • [Versatility]: Tapered Teeth Design starts threading more easily and smoothly, and prevents over-threading. Suit for creating new threads or repairing damaged threads on metals like carbon steel, cast iron, aluminum and stainless steel..
  • [Most Common Sizes in Metric]: This tap and die set comes with 110 pieces totally in a storage case. This metric tool set Include: 1) 35 pcs plug taps.
  • [Portable Case]: Each tap and dies set is equipped with a iron toolbox which is engraved with corresponding scales. And it’s convenient to store them in the case to prevent dust..
Check Stock

Muzerdo 110PCS Standard Sae and Metric Bearing Steel Tap and Die Rethreading Kit

  • ...1.25, 14x1.5, 14x2, 16x1, 16x1.5, 16x2, 18x1.5,).
  • Tap wrenches (M3-M12 x 1/16”-1/2”, M6-M20 x 1/4”-3/4”).
  • Die wrenches (25mm x 1”, 38mm x 1-1/2” OD).
  • BUILT TO LAST: Constructed from chromium-coated high carbon steel for maximum strength and corrosion resistance.
  • Metric tap set has 3-4 flute abrasive cutting edges each so you can easily clean/repair and cut materials such as aluminum, iron, cast iron, alloy steel, carbon steel, abrasive steel, malleable cast iron, and other difficult to machine metal materials.
  • EASY STORAGE: Heavy-duty 17” x 2.25” x 12.75” inch (43.2cm x 5.7cm x 32.4cm) plastic blow-molded carrying case with 2 side latches and built-in handle for easy transportation, safe storage, and quick organization.
  • Each compartment is labeled with sizing for simple identification.
  • PACKAGE CONTENTS: Combination set contains both metric taps and dies.
  • Tap die set metric tap die metal threader package includes 35 taper taps, 35 plug taps, 35 dies, 2 tap holder wrenches, 2 die holder wrenches, 1 T-bar type tap wrench, and 1 carrying case.
  • (Thread pitch gauge not included, but we recommend using these taps to light up threads from the bolt).
Check Stock

Muzerdo 131PCS Sae and Metric Coated Bearing Steel Tap and Die Rethreading Kit

  • ...the set are handles for turning. The collection also consists of screw extractors and charts to determine the correct drill and taps to match the thread size and pitch. Some sets may contain twist-lock guides, coarse and fine taps, and other tools at a higher cost..
  • Instead of other kits which are made of low carbon steel, our kit are made of *** bearing steel*** which are more stronger, good abrasion performance. An overall chromium coating improves the corrosion resistance of the generally used through-hardening bearing steel. These cutting materials are suitable for threading steel, cast steel, cast iron, non-ferrous metals, plastics, softwood, and hardwood..
  • Known for their ability to start easily, these taps and dies are the most commonly used style and are perfect for most hand threading applications.
Check Stock

Muzerdo 115PCS Sae and Metric Bearing Steel Tap and Die Rethreading Kit with Metal Box

  • ...u can. That way you will be able to pull the right size out of the box when you need it..
  • Wrenches – All tap and die bits need to be mounted in a wrench. Broadly speaking, they are all roughly the same, with a few notable exceptions. The tap wrench from Muzerdo, is the best on the market..
  • Construction Material – Steel is the base metal used in the construction of these sets – but not all steel is created equally! Look for steel alloy or, even better, Titanium tipped cutting surfaces. The better the metal the tougher the tap and die so they so they can cut into more.
  • Metric/SAE – The size of the tap and die is also important. Metric is of course the European measurement system, SAE are based on US sizes (so use inches instead of millimeters). This is important as you may struggle to use a SAE tap and die set on a vehicle with metric measurements. If the car is made in the US, it probably uses SAE measurements. If it is a European carmaker, it’s probably the opposite. If can look for a set with dual Metric and SAE compatibility of course then you don’t have t.
  • Metal Storage Case – More than with many other types of tools, the storage case is an important part of the tap and die set. Frankly, because these sets can come with multiple parts, y....
Check Stock

Eco-Baeerss Tap and Die Set Metri_c and Standard M12 X 1.25mm Tap Die Set Right Hand

  • 【Model】M12 X 1.25mm tap and die set, pitch:1.25mm.
  • 【Material】This threa_d tap is made of H_S_S 6542, which is stronger and more durable than ordinary taps.
  • 【Scope of Application】 This product is suitable for stainless steel, iron, aluminum, copper, ordinary steel, wood and other materials. It can be used for hand-pulled or electric applications..
  • 【Package Included】 1 x tap and 1 x die.
  • 【After Sales Service】 Tap and dies support free returns and exchanges, our friendly customer service always supports our products and responds to all emails within 24 hours.
Check Stock

ATOPLEE Spiral Point Plug Threading Tap ,5pcs HSS 6542 Titanium Coated Metric Right Hand Thread Taps,M3-M8

  • ...u can. That way you will be able to pull the right size out of the box when you need it..
  • Wrenches – All tap and die bits need to be mounted in a wrench. Broadly speaking, they are all roughly the same, with a few notable exceptions. The tap wrench from Muzerdo, is the best on the market..
  • Construction Material – Steel is the base metal used in the construction of these sets – but not all steel is created equally! Look for steel alloy or, even better, Titanium tipped cutting surfaces. The better the metal the tougher the tap and die so they so they can cut into more materials and they will stay sharper for longer..
  • Metric/SAE – The size of the tap and die is also important. Metric is of course the European measurement system, SAE are based on US sizes (so use inches instead of millimeters). This is important as you may struggle to use a SAE tap and die set on a vehicle with metric measurements. If the car is made in the US, it probably uses SAE measurements. If it is a European carmaker, it’s probably the opposite. If can look for a set with dual Metric and SAE compatibility of course then you don’t have t.
  • Metal Storage Case – More than with many other types of tools, the storage case is an important part of the tap and die set. Frankly, b....
Check Stock

45 Pc Tap & Die Set Metric Mm Titanium Tungsten Steel Jumbo Thread Renew Tool

  • 86 Piece Tap and Die Set Bearing Steel Sae and Metric Tools, Titanium Coated with Metal Carrying Case.
  • Size:14.8 x 10.7 x 2.2"inch / 37.6 x 27 x 5.6cm. Weight:12lb / 5.4kg. Material upgrading:Alloy Steel 55¡ã- 60¡ã, Sizes Stamped Engraved-etched On the Metal.
  • SAE TAP SIZES and SAE DIE SIZES: 1/8"-27NPT, 4-40, 6-32, 8-32, 10-32, 10-24, 12-24, 1/4"-20, 1/4"-28, 5/16"-18, 5/16-24, 3/8"-16,3/8"-24, 7/16"-14, 7/16"-20, 1/2"-13, 1/2"-20, 9/16"-12, 9/16"-18, 5/8"-11, 5/8"-18.
  • METRIC TAP SIZES and METRIC DIE SIZES: M3-0.5, M4-0.7, M5-0.8, M6-1.0, M7-1.0, M8-1.0, M8-1.25, M9-1.25, M10-1.5, M10-1.25, M11-1.5, M11-1.25, M12-1.75, M12-1.5, M14-2, M14-1.5, M16-2, M16-1.5.
  • Ideal for rethreading fasteners and fastener holes for auto and machinery repair. Perfect set for the professional craftsman Tap and die set is designed to thread cutting: tap is used to process internal thread, while the die is for external thread.
  • Easy Storage: Heavy-duty plastic blow-molded carrying case for easy transportation, safe storage, and quick organization.
Check Stock

110 Piece Combination Tap and Die Set Alloy Steel 55°- 60° Metric Tools with Carrying Case + Free Glove Amazing Tour

  • 110 Piece Combination Tap and Die Set Alloy Steel Metric Tools with Carrying Case + Free Glove Amazing Tour.
  • Size:18 x 13 x 2.5"inch / 45 x33.5 x 6.5cm. Weight:14.3lb / 6.5kg. Material upgrading:Alloy Steel 55°- 60°, Sizes Stamped Engraved-etched On the Metal.
  • 35 Taper Taps + 35 Plug Taps + 35 Dies + 2 Tap Wrench M3-M12,M6-M20 + Die Wrench 25mm,38mm O/D + 1 T-Type Tap Wrench M3-M6 + 2 Antiskid Gloves.
  • Known for their ability to start easily, these taps and dies are the most commonly used style and are perfect for most hand threading applications.
  • Ideal for rethreading fasteners and fastener holes for auto and machinery repair. Perfect set for the professional craftsman Tap and die set is designed to thread cutting: tap is used to process internal thread, while the die is for external thread.
Check Stock

Machine Tap 1/2\-13 UNC Thread Pitch 4 Flutes, High Speed Steel Thread Forming Tap, Uncoated (Bright) Finish, Round Shank with Square End, Plug Chamfer, HSS Machine Screw Plug Tap

  • ...1.25, 14x1.5, 14x2, 16x1, 16x1.5, 16x2, 18x1.5,).
  • Tap wrenches (M3-M12 x 1/16”-1/2”, M6-M20 x 1/4”-3/4”).
  • Die wrenches (25mm x 1”, 38mm x 1-1/2” OD).
  • BUILT TO LAST: Constructed from chromium-coated high carbon steel for maximum strength and corrosion resistance.
  • Metric tap set has 3-4 flute abrasive cutting edges each so you can easily clean/repair and cut materials such as aluminum, iron, cast iron, alloy steel, carbon steel, abrasive steel, malleable cast iron, and other difficult to machine metal materials.
  • EASY STORAGE: Heavy-duty 17” x 2.25” x 12.75” inch (43.2cm x 5.7cm x 32.4cm) plastic blow-molded carrying case with 2 side latches and built-in handle for easy transportation, safe storage, and quick organization.
  • Each compartment is labeled with sizing for simple identification.
  • PACKAGE CONTENTS: Combination set contains both metric taps and dies.
  • Tap die set metric tap die metal threader package includes 35 taper taps, 35 plug taps, 35 dies, 2 tap holder wrenches, 2 die holder wrenches, 1 T-bar type tap wrench, and 1 carrying case.
  • (Thread pitch gauge not included, but we recommend using these taps to light up threads from the bolt).
Check Stock

Hanson 12008 1\ Rd Hex Plain Die Stock for Tap Die Extraction

  • ....8, 6x1.0, 7x1.0, 8x1.25, 9x1.25, 10x1.0, 10x1.5, 12x1.75.
  • UNC dies 4-40, 6-32, 8-32, 10-24, 12-24, 1/4, 5/16, 3/8, 7/16, 1/2.
  • UNF dies 10-32, 1/4, 5/16, 3/8, 7/16, 1/2.
  • BUILT TO LAST: Constructed from hardened alloy steel for maximum strength and longevity.
  • Can cut materials such as cast iron, steel, aluminum, copper.
  • EASY STORAGE: Heavy-duty plastic blow-molded carrying case for easy transportation, safe storage, and quick organization.
  • CONTENTS: Package includes coarse and fine threads numbered taps and dies from #4-40 to #12-24 and fractional taps and dies from 1/4"-28 to 1/2"-20, 1/8"-27 NPT tap and die, metric tap and dies from M3x0.5 to M12x1.75, thread gauge, tap handle, die handle, small tap chuck, and a carrying case for your convenience.
Check Stock