MakerFocus TFT LCD Screen Display 1.3inch TFT LCD Module, 240 * 240 IPS 65K Full Color 3.3V with SPI Interface ST7789 IC Driver, 51 STM32 Ar duino Routines for DIY
- User Manual: Please get the link from the product guide and description below.
- 1.3inch TFT LCD Screen Display Module: The TFT display provides a semiconductor switch for each pixel and each pixel is directly controlled by pulse. Therefore, each node is relatively independent and can be continuously controlled, which not only improves the response speed of the display, but also can be accurately controlled..
- Dot Size: 240*240 ( There are two display way: horizontal display and vertical display, you can adjust the display direction. ).
- We Have a Strong After-sales Service Team: As long as you have any questions about the product, we will resolve your issue immediately if received your email, your satisfactory purchase experience is our greatest hope! How to email us? Plz click “MakerFocus” and click “Ask a question” to email us! Looking forward to your consultation!.
Check StockDIYmalls ILI9341 3.2 inch TFT LCD Display Screen Module 3.3V Resistive Touch Panel 320x240 w/SD Card Slot for Mega 2560 only
- ILI9341 tft display has 40 pins, so it is not compatible with uno r3 and nano..
- ILI9341 display works at 3.3V. If you use it with mega 2560, please insert TFT 3.2 shield, not directly connect board with tft lcd module..
- You may need to set a suitable parameter in sketches to use this 3.2" touch screen, but it is not a difficult task..
- If you have any problem, please contact seller as follow: click "DIYmalls"(you can find "Sold by DIYmalls" under Buy Now button), in the new page, click "Ask a question"..
- ili9341 3.2 inch tft lcd can not work with esp32 board due to no SPI interface..
Check StockBOSS Audio Systems HIR8BGTM 8-Inch Universal Headrest - Discontinued by Manufacturer
- Built-in Dual Channel Infrared Transmitter.
Check StockExtech 380193 Passive Component LCR Meter
- For detecting NPN and PNP transistor, capacitor, resistor, diode, triode, N-channel and P-channel MOSFET, IGBT, JFET, triac and battery, resistor and capacitor and other components, etc..
- Put the pins of component in corresponding area, then dial the little handle and the detector will test it automatically, finally the results will display on the back light TFT screen clearly. ( Use 12864 liquid crystal display with green backlight)..
- Measurement results represent by TFT graphic display(160x128). Support Chinese and English..
- After detection, align the infrared remote control with the "IR" light, then press the button in the remote control, if the detector successfully decode it, it will display the data code and infrared wave form..
- One button operation, automatically detect and shutdown, and you can also press the multi-functional button to close the detector..
Check StockSlimpal Smart Scale with Body Fat and Water Weight WiFi and Bluetooth Rechargeable Digital Bathroom Scale Large Display for Heart Rate Weight Trend 15 Body Composition BMI Analyzer
- [2.4Ghz WiFi Bluetooth Auto Switch] Slimpal smart scale supports 2.4Ghz WiFi connections, more stable and convenient. After weighing, your data will....
- [Body Fat Rate on TFT Display Directly ] Upgraded design with premium TFT LCD screen display, Slimpal body fat scale built in algorithm can....
- [ Weight Trend &Heart Rate on TFT Display Directly] Not only body weight ,you can also check Heart Rate on the scale now! This smart scale with body....
- [Automatically Recognized & Unlimited Users] Slimpal smart scale is coated with conductive glass ITO,much larger sensor area than the metal electrodes....
- [Work with fitness App] Download Slimpal”App（iOS App Store or Play Store for Android), compatible with Apple Health, Google Fit and Fitbit. Plus,....
Check Stock1.3\ TFT LCD Display HD IPS 65K 240 * 240 3.3V with SPI Interface ST7789 IC Driver, 51 STM32 Ar for Arduino Routines
- User Manual:Adafruit_GFX:https://www.arduinolibraries.info/libraries/adafruit-gfx-library.
- Adafruit ST7789:https://www.arduinolibraries.info/libraries/adafruit-st7735-and-st7789-library.
- 1.3 inches colorful display lcd screen:This display is a thin film transistor type liquid crystal display and is true "Thin Film Transistor" (TFT).
- Dot Size: 240*240 ( There are two display way: horizontal display and vertical display, you can adjust the display direction).
- We have always cared about the customer experience and improve the product function details.
Check Stock
LCD Touch Panels Touchpanel Analog for DOGM128-6 (EA TOUCH128-1)
- ...fers 1 G Hz Cortex A8 CPU driving device and 256 Flash memory for HMI projects. You also get RS232/TTL UART Interface and USB port. The module is compatible with 7/28V wide operation voltage. (This is an excellent choice for your Arduino and Raspberry Pi projects.).
- Clear, Detailed, Hi Res HD - Our Smart HMI TFT LCD display offers excellent 800x480 high resolution with 4-wire resistance touch screen. Rich 262K (18bit) color for high color restore. Rectangular ratio 16:9 display format conversion. 70°/70°/50°/70° wide viewing angle, adjustable brightness（300 cd/m²) , TTF Font and contrast (500:1) offers you the ultimate project experience to accomplish more with improved results..
- Ultimate TFT LCD Display Module for Industry - SCBRHMI Intelligent TFT-LCD Module Model STWI070WT-01 is a customer favorite for a wide range of industrial and business applications. You get highest quality with the most usable functions. Often purchased for equipment in medical, beauty, engineering, industrial control, electric power, civil electronics, automation, traffic, new energy, and IOT applications..
- Generous 3 Year Warranty - We make SCBRHMI products to last and work well on the job. If this breaks, return it and we will replace it at no cost. Our displays ....
Check Stock
Ickiya MKS Gen L V2.1 3D Printer Control Board Motherboard, Open Source Marlin Support TMC2209/TMC2208/TMC2208/TFT35 V3.0/TFT35 E3/BL TOUCH/LCD12684 for Ramps 1.4 /Ramps 1.5/Ramps 1.6 3D Printer
- ✅Integrate 2560 and ramps1.4 are intergrated on a piece of board, which solves the problem of complicated and easy failure for Ramps1.4 composite interface.Users can change their own motor drive, support A4988/TMC2209/TMC2208/TMC5160/DRV8825 stepper drivers.
- ✅Using CH340 serial chip to ensure the stable and reliable premise, reduce the cost, and to solve the problem of the previous 16U2 hard drive.Using the open source firmware for Marlin, the configuration is exactly the same as for ramps1.4, and can replace for Ramps1.4 directly..
- ✅24V input can be accepted, and the same system power can reduce the hot bed current to 1/4, effectively solving the hot bed MOS tube heating problem..
- ✅It can be directly connected to 2004LCD display and 12864LCD display, and can be supported by TFT28 /TFT32/TFT35/TFT50/TFT70 touch screen..
- ✅The XYZ axis adopts the terminals of different colors to correspond to the motor and the limit switch, and the connection is convenient,reduces the probability of inserting and reversing, and prevents the main board from being damage by the oppsite inserted of the drive..
Check Stock
Naroote Display Module, TFT LCD Touch Panel Serial Port Module + ILI9341 5V/3.3V 2.8\ 240x320 -Product Quality Assurance
- ...ries 4.3" TFT LCD module can be controlled by any MCU. This offers 1 G Hz Cortex A8 CPU driving device and 128 Flash memory for HMI projects. You also get RS232/TTL UART Interface and USB port. This is an excellent choice for your Arduino and Raspberry Pi projects..
- Clear, Detailed, Hi Res HD - Our Smart HMI TFT LCD display offers excellent 480x272 high resolution with 4-wire resistance touch screen. Rich 262K (18bit) color for high color restore. Rectangular ratio 16:9 display format conversion. 70°/70°/50°/70° wide viewing angle, adjustable brightness（300 cd/m²) , TTF Font and contrast (500:1) offers you the ultimate project experience to accomplish more with improved results..
- Ultimate TFT LCD Display Module for Industry - SCBRHMI Intelligent TFT-LCD Module Model STWC043WT-01 is a customer favorite for a wide range of industrial and business applications. You get highest quality with the most usable functions. Often purchased for equipment in medical, beauty, engineering, industrial control, electric power, civil electronics, automation, traffic, new energy, and IOT applications..
- Generous 3 Year Warranty - We make SCBRHMI products to last and work well on the job. If this breaks, return it and we will replace it at no cost. Our displays ....
Check Stock
BIGTREETECH TFT35 E3 V3.0.1 Touch Screen Display RepRap Smart Controller Panel Compatible with SKR Mini E3 SKR E3 DIP Board for Ender 3 CR10 3D Printer
- ... designed for ender 3 3d printer especially, which can be a drop-in replacement for its original LCD screen..
- ❤【Two Working Modes】TFT35 E3 V3.0.1 touch screen support UART serial port screen mode (touch screen mode) and 12864 screen mode, it can replace original display of Ender 3 3D printer. You can enjoy two printing modes: SD card and U disk..
- ❤【More Extension Ports is Reserved】TFT35 E3 V3.0.1 display r eserve the extension port of filament breaking detection,automatic shutdown after printing,also WIFI function can be realized by external WIFI module through WIFI port..
- ❤【Firmware Update】 TFT35 E3 V3.0.1 is easy and convenient to update firmware by SD card,download from our github, copy and save it to SD card.firmware must bed reserved ,then re-plug the SD card and wait to 10s.The firmware has been successfully updated..
- ❤【Quality Warranty 】TFT35 E3 V3.0.1 touch screen is designed and produced by BIGTREETECH team,any questions and feedback about that please free to tell us, we have professional technical team to support you..
Check Stock
BIGTREETECH SKR Mini E3 V3.0 Control Board Integrated TMC2209 UART Stepper Driver Supports Marlin/Klipper Compatible Ender 3/Ender 3 Pro/Ender 3 V2 3D Printer Motherboard ZZB000590 Black
- ⭐【Main Control Chip】BIGTREETECH SKR Mini E3 V3.0 control board adoptes the G0 series MCU-STM32G0B1RET6 or STM32G0B0RET6 ARM Coretex. integrated TMC2209 Silent stepper motor drive,Support runing Klipper&Marlin..
- ⭐【Heat Sink Design Upgrade】New upgraded to integrated large stepping motor driver aluminum heat sink,strengthen the drive heat dissipation capacity, and greatly improve the motherboardc heat dissipation performance..
- ⭐【Multiple Functions】It Supports BLTouch, RGB lights,Filament detection, Automatic shutdown,power-off reesume, Display supports TFT35 E3 V3.0.1/TFT35 V3.0.1/TFT28/TFT43/TFT50/TFT70 V3.0 touch screen as well as original 12864 LCD of Ender 3 printer..
- ⭐【Fan Upgraded】Increase Three CNC heat dissipation controllable fan interface to reduce the printer temperature when the device is working..
- ⭐【Multiple Compatibile】BIGTREETECH SKR MINI E3 V3.0 Control board is design for Ender 3,plug and play,compatible with Ender V2 Ender 3/ende 3 pro/ender 5/ender 5 pro/CR-10 3D printer, the firmware is pre-install well before we ship out, you can select the firmware base on your needs..
Check StockBIGTREETECH Upgrade PITFT50 V2.0 Graphic Smart Display DSI Interface 5 inch LCD Touch Screen Suitable for Raspberry Pi
- 1) This is a 5-inch LCD touch screen with a resolution of 800 x 480 for Raspberry-Pi. The display area can reach 108 x 64.8mm..
- 2) Adapt to the Raspberry-Pi DSI display interface, directly driven by DSI.
- with a capacitive touch panel. Supports 5-point touch..
- 3) The unique hole design on the back allows you to install the Raspberry-Pi directly. PI TFT50 display adopts Raspberry-Pi power supply design, no external power supply is needed..
- 4) The PI TFT50 display supports hardware backlight adjustment, and the backlight brightness can be adjusted by rotating the potentiometer behind the screen..
- 5) If you encounter any problems after receiving the product, please contact us via Amazon. We have professional technical after-sales personnel to solve your problems. Thanks for your cooperation..
Check StockMTBs Engage E-Boats : 10 June 1944
- The kit includes 48V1500 DC motor with MTX Sun Ringle bicycle rim(no tire), 35A max controller, throttle, brake lever, UKC1 TFT display and 7 speed gear. No battery included!.
- Top speed: 57-58km/h(35mile/h) goes with 26inch wheel.
- Big torque, 45N./M, good ability to climb the hills.
- Motor: 180 copper winding+ best quality magnet, hub width: 135mm for rear Wheel.
- MTX Sun Ringle Bicycle RIm, rim width: 38.9mm..
- UKC1 TFT display with 3.5” high contrast color screen shows battery power level, time, speed, mileage, gear, input power. Components error checking and report.
- Pedal Assistance System (PAS)to let you enjoy cycling while driving electric bike..
Check Stock
