Categories

Best Thermistor 3d Printer

USA Import Material 200x200mm 300W 24V Cube Flexible Silicone Heater Compatible with Voron V2.4 Prusa i3 RepRap 3D Printer Heated bed 24V

  • used for printing area 200x200mm 3D printer.
  • With 1meter NTC 100K 3950 thermistor for temperature Control. Power consumption: 300W. Attached with two pieces 1meter length power wire.
  • This heated bed is used with 200x200mm printing area 3D printers, but also compatible with Voron V2.4 3D printer which printing area is 250x250mm..
Check Stock

TRONXY Original Extruder Assembled MK8 Hotend Kit for 3D Printer with Aluminum Heating Block, 1.75mm, 0.4mm Nozzle，Bowden Extruder kit

  • 100% TRONXY Orginal MK8 Full Set Hotend Kit.
  • Suitable For TRONXY XY-3 Seriers 3D Printer.
  • Tip of the nozzle, aluminum heating block, throat pipe (built-in Teflon).
  • MK8 Extruder Hot End Kit With thermistor 100K and Heater 24V 50W.
  • Thermistor and heater cable length: 1.2 m ,Feed tube:50cm.
Check Stock

Ewigkeit MK8 Hotend Ender 3 and Pro Assembled Extruder with Aluminum Heating Block 0.4mm Nozzle(24V 40W)

  • Ender 3 hot end with 100% original and high quality accessories for Creality 3D printer.
  • Ender3 pro Work with different sizes of MK8 nozzle: 0.2mm 0.3mm 0.4mm 0.5mm 0.6mm 0.8mm 1.0mm.
  • MK8 Extruder Hot End Kit, white wire is temperature thermistor, red wire is heater cartridge is 24V 40W.
  • Tip of MK8 0.4mm nozzle, aluminum heating block, throat pipe (built-in Teflon) for 1.75mm filament.
Check Stock

AITRIP 10PCS 3D Printer Removable 3950 NTC 100K Thermistor Sensor Compatible with Creality Ender 3 5 CR10 CR-10 CR10 Anet A8 Prusa i3 MK8

  • Temperature sensor 100KΩ accuracy of ± 1%, Total length:1 Meter.
  • Compatible with Creality CR-10S Pro,CR-X,Ender 3, Ender 3X, Ender-3 Pro, Prusa I3, Anet E10 etc.
  • AITRIP Thermistor Sensor is Removable design and Easy to install.
  • Package include: 10 thermistors. Threre is no HX2.54 connector at the end of the thermistor..
  • Use for heated bed or extruder of 3D Printer, with DuPont connectors..
Check Stock

MK8 Extruder Hotend 3D Printer Assembled kit for CR-10/CR-10S/CR-S with Aluminum Heating Block 1.75mm, 0.4mm Nozzle

  • 100% original and high quality 3D Printer accessories for Creality CR10/ CR10S/ CR10S4/ CR10S5.
  • MK8 Extruder Hot End Kit, white wire is temperature thermistor, red wire is heating tube 24V 40W.Perfect replacement accessories/parts for Creality CR-10 CR-10S S4 S5 3D Printer.
  • This CR-10 hotend can work with different sizes of MK8 nozzle: 0.2mm 0.3mm 0.4mm 0.5mm 0.6mm 0.8mm 1.0mm nozzle.
  • Tip of MK8 0.4mm nozzle, aluminum heating block, throat pipe (built-in Teflon) for 1.75mm filament.
  • With nine(9) cooling fins on the heatsink.No blockage,no leakage,fast heat dissipation, better printing effect..
Check Stock

CR10 S5 Silicone Heater Pad 508 x 508mm 20 X 20 Heated bed w/ 24 Holes For Creality CR-10 S5 3D Printer Large Print Bed Adhesive Backing + Sensor 120V

  • This silicone heating pad with 24 pre-made screw holes with dia 12mm as the picture shows is designed for creality CR-10 S5 3D printer building....
  • Our Manufactuer use Arlon silicone rubber substrate imported from the United States and 3M Adhesive Backing, highest quality. Each heated bed is....
  • CR10 S5 3D printer high temperateure heated bed.
  • Size: 508mmx508mm With 2 meters NTC 100K 3950 thermistor for temperature Control. Power consumption: 1300W Attached with two pieces 2meters length....
  • Caution! Before buying, please check if the 24 hole pattern conforms to that of your build plate. Pattern view from the adhesive side of this heater....
Check Stock

Wisamic Silicone Rubber Heater 310x310mm 120V 750W, with 3M Tape Screw Holes for 3D Printer CR-10 CR-10S S3

  • The silicone rubber heater can prevent condensation in motors or instrument cabinets..
  • Applications for food service equipment, airplane engine heaters, aerospace industry, drums and other..
  • Comes with 4 pre-made screw holes as the picture..
  • Specially designed to fit the 3D Printers CR-10 CR-10S S3. Excellent heat source for your CR-10/10S3D Printer..
Check Stock

Upgrade M3 Hex Screw in Fixing Thermistor 100K 3950 Temperature Sensor for Ender 3 V2 Pro CR10 and Other 3D Printer Extruder Hotend 100K 3950

  • M3 screw for installation is Quik and Durable, Flexible and Long Lasting, longer life span.
  • DIY players can also modify BLOCK by themselves. Make an M3 threaded hole in BLCOK, then you can use this thermistor.
  • Thermistor model: NTC 100K 3950. HERE is the firmware setting: *13:100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " &"Hotend "All In ONE"....
  • For the printer which uses NTC 100K 3950 thermistor, Then this thermistor is plug and use.
Check Stock

Sunhokey Extruder Assembled MK8 Hot End Kit for CR10 with Aluminum Heating Block, 1.75mm, 0.4mm Nozzle(12V 40W)

  • High-quality 3D Printer accessories for Creality CR-10 CR-10S S4 S5..
  • Work with different sizes of MK8 nozzle: 0.2mm 0.3mm 0.4mm 0.5mm 0.6mm 0.8mm 1.0mm nozzle..
  • MK8 Extruder Hot End Kit, the white wire is temperature thermistor, the red wire is heating tube 12V 40W..
  • Tip of the nozzle, aluminum heating block, throat pipe ..
Check Stock

MK10 3D Printer Extruders Kit 5 Pcs Aluminum Heater Block + 1.75mm Extruder Throat Tube M7 Thread + Cotton Heater Tape for 3D Printer Wanhao Filament

  • ✹✹ High quality copper and stainless steel, ensure concentricity and roundness.
  • Designed for many common types of 3D printers, solid aluminium construction with aperture..
  • ✹✹ Aluminium Heater Block for Extruders in 3D-Printers. A drilling with an M4 screw is scheduled for the optimal fixing of the Cartridge Heater. The Thermistor is fixed by means of a M4 grub screw in order to avoid slipping or loosening. The heating block is equipped with an M7 thread for the Nozzle..
  • ✹✹ Compatibility: Fit with MK10 hotend aluminum cooling block, such as DIY MK10 3D printer, FlashForge Creator Pro, FlashForge Creator X, FlashForge Dreamer, Dremel Idea, Builder PowerSpec 3D, Pro PowerSpec 3D X, Wanhao Duplicator 4S, Wanhao Duplicator 4X, Wanhao i3, etc..
  • ✹✹ 2mm thick cotton heater tape for heat preservation, keep heater block and consumable work better..
  • ✹✹ Any questions, you can tell us and we will give you a satisfied solution!.
Check Stock

300 X 300mm (Approx. 12' X 12') 120V 750W, KEENOVO Universal Flexible Silicone Heater Mat/Pad, 3D Printer Heated Bed Heating Element

  • Wonderful silicone heater for your 3D printer heat-bed. Fast Heating with 5.2W per square inch..
  • surface mount NTC 100K thermistor ( R-T table available).
  • 3M adhesive backing offers excellent and easy mounting..
  • Versatile and may be used in many other applications..
Check Stock

Genuine E3D Hotend Thermistor Cartridge Replacement

  • Direct replacement of cartridge type thermistor in E3D hotends..
  • A custom made thermistor encapsulated into an easy to use cartridge package..
  • Comes with (1) Hotend Thermistor with attached connector and (1) connector cable measuring 40 inches (101cm).
Check Stock

24V 40W 620 Ceramic Cartridge Heater with 3950 100K NTC Thermistor with 1 Meter Wiring for RepRap 3D Printer Heatbed Hot End

  • 1 Meter long wire with high temperature PTFE insulated wiring and female pin head, 1.25mmx2.0mm glass bead.
  • Temperature sensor 100KΩ accuracy of ± 1%.
  • 24V 40W 620 Ceramic Cartridge Heater and NTC Thermistor 100K 3950 for 3D Printer Creality CR-10S Pro, CR-X,Ender 3,Ender 3 Pro, Ender 3 V2,Prusa....
Check Stock