Categories

Best Ttl Logic

DTECH FTDI USB to TTL Serial 3.3V Adapter Cable TX RX Signal 3 Pin 0.1 inch Pitch Female Socket FT232RL Chip Windows 11 10 8 7 Linux MAC OS 6ft Black

  • 6 ft USB to TTL serial adapter (with 3 pin 0.1” pitch female header socket) connects devices with 3.3 V logic level UART signals interface to a....
  • A genuine FT232RL chip module is housed in USB 2.0 type A male terminal for wider compatibility and supports reliable data transfer rates.
  • 6 feet FTDI USB to TTL serial cable (3 way output flying leads ) provides access to UART (transmit) Tx, (receive) Rx and GND.
  • FTDI chipset on the PCB board has configurable internal EEPROM and 3.3V UART signals can be individually inverted by configuring the EEPROM.
  • 3V3 TTL to USB converter cord is compatible with Windows 11, 10, 8, 8.1, 7 (32, 64-bit), 2008/XP/Vista/CE, Mac OS, Linux 2.4 and greater.
Check Stock

DTECH USB to TTL Serial 3.3V Adapter Cable TX RX Signal 4 Pin 0.1 inch Pitch Female Socket PL2303 Prolific Chip Windows 10 8 7 XP Vista (6ft, Black)

  • 6 ft USB to TTL serial adapter (with 4 pin 0.1” pitch female header socket) connects devices with 3.3 V logic level UART signals interface to a laptop via USB port.
  • A genuine PL2303TA chip module is housed in USB 2.0 type A male terminal for wider compatibility and supports reliable data transfer rates.
  • 6 feet USB to TTL serial cable 3V3 (4 way output flying leads ) provides access to UART (transmit) Tx, (receive) Rx, VCC (5V) and GND.
  • PL2303 Prolific chipset on the PCB board has configurable internal EEPROM and UART signals can be individually inverted by configuring the EEPROM.
  • 4 pin 3.3V USB to TTL converter cord Compatible with Windows 10, 8, 8.1, 7 (32, 64-bit), 2008/XP/Vista/CE.
  • ideal USB 2.0 debug cord for Vendor ID re-write, router, GPS, set top box, transmitter, flash firmware on hard drive, etc..
Check Stock

Juried Engineering LM339N LM339 Quad Differential Comparator Industrial Grade Breadboard-Friendly IC DIP-14 (Pack of 5)

  • SINGLE-CHANNEL: TLV3501 is a single-channel high-speed push-pull output comparator, delay is 4.5ns, supply voltage: + 2.7V to + 5.5V.
  • FRONT SHAPING MODULE: This module can be for a wide range of voltage signal shaping period, as the frequency, phase difference time domain measurements and other front-end conditioning module.
  • CMOS AND TTL: Rail-to-rail output can directly drive a CMOS or TTL logic.
  • EASY TO OPERATE: Without threshold setting, the sine wave, square wave and triangular wave can be transformed into square wave, which can be used easily without debugging.
  • GREAT EXTENSIBILITY: At the same time, it has great extensibility, just change a small amount of the original.
Check Stock

SainSmart 8-Channel Relay Module

  • 5V 8-Channel Relay interface board, and each one needs 15-20mA Driver Current.
  • Equipped with high-current relay, AC250V 10A.
  • Standard interface that can be controlled directly by microcontroller (Arduino , 8051, AVR, PIC, DSP, ARM, ARM, MSP432, TTL logic).
  • Indication LED's for Relay output status.
Check Stock

Valefod DC 5V Relay Module 1-Channel Relay Switch with Optocoupler Isolation High/Low Level Trigger, Pack of 10

  • 【Control Devices】The 1-channel relay module uses genuine high quality DC5V relay and SMD opto-isolator supporting high/low level trigger, widely apply to control various AC/DC appliances, and other devices with large current..
  • 【Load Range】NO(Normally open) maximum load < AC 250V/10A, < DC 30V/10A. Trigger current of opto-isolator: 5mA..
  • 【Fault-tolerant Design】The relay will not operate even if the control line is disconnected..
  • 【Universal Interface】Equipped with screwed terminal plate and fixed bolt holes(diameter: 3.1 mm) on both sides for easy installation..
  • 【High Compatibility】The relay module can be controlled directly by 5V logic signals from microcontroller(8051, AVR, PIC, DSP, ARM, Raspberry Pi, MSP430, TTL logic etc).
Check Stock

ELEGOO 8 Channel DC 5V Relay Module with Optocoupler Compatible with Arduino UNO R3 MEGA 1280 DSP ARM PIC AVR STM32 Raspberry Pi

  • 5V 8-Channel Relay interface board, each one needs 70mA Driver Current.
  • Equiped with high-current relay, AC250V 10A.
  • Each relay has normally open and normally closed contact. Can be selected by jumper relay and TTL or ground..
  • With power indicator,8-way road has a status indicator. With a relay coil to absorb the diode protection..
  • Standard interface that can be controlled directly by microcontroller (Arduino , 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic).
  • The 8 channels are optically isolated, safe, reliable, anti-interference. Widely used for all MCU control, industrial sector, PLC control, smart home control。For a complete data sheet for this relay board, please download it from: http://dwz.win/UhW.
Check Stock

SainSmart 16-Channel 12V Relay Module Board for Arduino DSP AVR PIC ARM

  • 12V 16-Channel Relay interface board, and each one needs 15-20mA Driver Current.
  • Equipped with high-current relay, AC250V 10A.
  • Standard interface that can be controlled directly by microcontroller (Arduino , 8051, AVR, PIC, DSP, ARM, ARM, MSP433, TTL logic).
  • Indication LED's for Relay output status.
Check Stock

50pcs NE555P Single Precision Timer Timer Chip IC Pulse Generator 4.5V-18V 10mA Compatible with TTL CMOS for Household Appliance and Electric Toys

  • The monolithic NE555 timers are controllers able to make precise time delays or oscillation very stable. The delay range is extremely wide and may vary from a few microseconds to a few hours..
  • Can be matched with TTL,CMOS and other logic circuits, its output level and input trigger level, can correspond to the high and low levels of these series of logic circuits..
  • high timing accuracy and good temperature stability. Widely used in waveform generation and transformation, measurement and control, household appliances, electronic toys..
  • 50pcs NE555P Timer IC packed in a plastic box for better protection..
Check Stock

Weewooday 15 Pieces 5V Relay Module 1- Channel Relay Control Boards with Optocoupler Isolation High and Low Level Trigger Expansion Board

  • Relay module: this relay board supports high and low level trigger and can be controlled by any 5V digital output of the microcontroller.
  • Parameter details: maximum load of normally open interface: AC 250v/ 10A, DC 30v/ 10A, trigger current is 5mA.
  • The 5v relay control board adopts SMD optocoupler isolation, which has strong driving ability and stable performance.
  • Practical design: with fault-tolerant design, the relay module will not operate even if the control line is disconnected.
  • All interfaces can be provided through directly connected terminal s since the humanized interface design, it is very convenient to use.
  • High compatibility: the relay module can be directly controlled by the 5V logic signal provided by the microcontroller, suitable for 8051, Raspberry Pi, PIC, DSP, ARM, AVR, MSP430, TTL logic, etc..
  • Wide application: this 5V relay board can be applied with Raspberry/ CNC machine/ ARM/ PIC/ AVR/ MCU/ PS4 and more.
Check Stock

BOJACK 16-pin IC Stepper Motor Drivers Controllers L293 L293D （Pack of 10 Pcs）

  • Channel Capability: 600mA output current channel..
  • Peak Output Current: 1.2A Channel (non repetitive)..
  • Advantages: High temperature protection, easy to use..
  • Design: Built-in clamping diode, monolithic integrated high-voltage, high-current four-channel driver, accept standard DTL or TTL logic level..
Check Stock

AOICRIE 12V 16-Channel Relay Interface Board Module Optocoupler LED LM2576 Power for Arduino DIY Kit PiC ARM AVR

  • ★12V 16-Channel Relay interface board, and each one needs 15-20mA Driver Current.
  • ★Equipped with high-current relay, AC250V 10A.
  • ★The control signal voltage range: the trigger signal is low 0-2V.
  • ★Standard interface that can be controlled directly by microcontroller (for Arduino , 8051, AVR, PIC, DSP, ARM, ARM, MSP433, TTL logic).
  • ★DC 12V 16 Channel Relay Module Interface Board With Optocoupler Protection LM2576 Power for Arduino DIY Kit.
Check Stock

Dorhea 37 in 1 Sensor Modules Kit with Tutorial for R3 Board Mega2560 Mega328 Nano Compatible with IDE Raspberry Pi

  • 37 in 1 sensor module Kit is complete update and common models,compatible with arduino R3, MEGA 2560, NANO and Raspberry pi..
  • All components compatible with Arduino IDE, can be used directly..
  • Standard interface can be controlled directly by microcontroller ( 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic)..
  • Upgraded tutorial only for R3, MEGA2560 R3, NANO in CD, There are tutorials in the CD that comes with..
  • Complete Update and common models for arduino NANO R3 Mega 2560 starter kit..
Check Stock

Qunqi 4pcs 5V 2 Channel 5V Relay Module with Optocoupler Low Level Trigger Expansion Board Compatible with R3 MEGA 2560 1280 DSP ARM PIC AVR STM32 Raspberry Pi

  • Indication LED's for Relay output status.
  • IN: can be high or low level control relay.
  • Equiped with high-current relay, AC250V 10A.
  • Standard interface that can be controlled directly by microcontroller (Compatible with , 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic).
Check Stock