Categories

Best Variable Load Flasher

DC 4.5-30V 10Amp Blinking Flasher Module

  • This is a simple and practical blinking flasher module, the ON and the OFF duration can be adjusted separately. The blinking flasher module is suited for both resistive and slightly inductive loads. This blinking flasher module is ideally suited for driving for example LED lamps, hazard lights, warning signs, safety beacons, DC light bulbs, etc .....
  • Operating voltage DC 4.5 to 30V. Maximum current: 10 Amp. Maximum load 300 Watts/at DC 30V, 120 Watts/at DC 12V. (NOTE: this product no step-up, step-down or inverter function, only for DC load).
  • Time-ON 0.01 to 15 seconds and Time-OFF 0.01 to 15 seconds adjustable. The output ON - OFF - ON – OFF… cycle alternates..
  • Two precise 25-turn adjustable potentiometers, you can use a screwdriver to easily adjust the ON and OFF time you need. With LED indication for output status..
  • Compact plastic case and wires connects for easy mount. Two screw mounting holes are convenient for you to fix it on the wall or wooden board. Of course, you can also choose not to lock the screw..
Check Stock

Xotic Tech 1pc 12V 3-Pin CF14 EP35 Flasher Relay for LED Turn Signal Light Bulbs Compatible with Audi or BMW or Chevrolet or Chrysler or Dodge or Ford or GMC or Hyundai or Jaguar or Lexus

  • This CF14 Electronic LED Flasher Relay operates at 12V and will compatible with Hyper Flashing for various vehicles. Please make sure your vehicle using 3-pin CF14 before purchase..
  • The installation is easy plug and play to replace the stock relay in the fuse..
  • This LED flasher is compatible with those are shown below with a simple plug and play without adding a set of external load resistors: Compatible with Audi.
  • Replace the stock relay in the fuse box..
  • Please make sure your vehicle use 3-pin CF14 configuration as graph above before purchase. You can usually find the flasher pin right on your flasher..
Check Stock

NTHREEAUTO 2 Pin Electronic Flasher Relay, Adjustable 12V Relays Fix for LED Turn Signal Hyper Flash, Universal

  • Speed Adjustable - Fix motorcycle turn signal hyper flash, allow LED light to blink at the normal rate, anticlockwise turn faster, clockwise turn slowly..
  • Parameter - Flashing Frequency: 50 times/min to 200 times/min. Operating Voltage: 12V (11V-15V). Switch Power: 0.02A to 12A. Working Temperature: -40°C to +80°C. Max Power: 42W, means that the power of all LED bulbs must be low than 42 W. If more than 42 W, may required install load resistors..
  • Waterproof - Turn signal flasher relay is waterproof design, stable and durable, easy to install..
  • Plug and Play - Directly replace the old relay. Eliminate the need for tapping wires to install the load resistors..
  • Buy with Confidence - Package included: 1PC 2 Pin motorcycle LED flasher relay.
  • You are backed by 6-Month warranty since order purchase date.Please feel free to contact us if you have any questions..
Check Stock

XtremeAmazing 5 Pin EP27 FL27 Electronic Flasher Relay for Car Vehicle LED Turn Signal Light Bulbs Hyper Blink Flash Fix

  • 2 pin CF12 12V LED Flasher Relay. Suitable for motorcycle or scooter use to prevent turn signal hyper flashing.
  • Eliminates the need for load resistors, turn signals will flash at normal rate with or without LED bulbs.
  • Cubic shape 2-prong/pin CF-12 LED flasher (Size: 1.43 x 1.33 x 1.00").
  • Work for cars or motorycles to fix the fast/rapid flashing turn signal or prevent weak or non flashing LED blinking issues.
Check Stock

DEWHEL 12V 0.02A-10A 2-Pin CF-12 Electronic LED Flasher Relay Fix for Turn Signal Light Fast Hyper Flash

  • 2 pin CF12 12V LED Flasher Relay. Suitable for motorcycle or scooter use to prevent turn signal hyper flashing.
  • Eliminates the need for load resistors, turn signals will flash at normal rate with or without LED bulbs.
  • Cubic shape 2-prong/pin CF-12 LED flasher (Size: 1.43 x 1.33 x 1.00").
  • Work for cars or motorycles to fix the fast/rapid flashing turn signal or prevent weak or non flashing LED blinking issues.
Check Stock

Yibid LED Integrated Tail Light Replacement for Honda Grom MSX 125 Motorcycle 2014-19, Brake Indicator Sequential Lights for MSX125/SF CBR650F CTX700 CTX700N, Smoke len with 1pcs 2-Pin Flasher Relay

  • Brand New Taillight assembly With 1pcs 2-pin Black Led turn signal flasher relay(B pole=Input，L pole= output) ；No instruction! Need to install skills，Professional installation is Recommended.
  • Package Included: 1pcs Taillight assembly & 1pcs 2-pin Black Led turn signal Flasher relay (NO taillight Relay Including!!! you can used your store one) Fitment :For MSX125 CBR650F CTX700 CTX700N.
  • Wire Connection: Black Line:Negative ；Red Line:Red Lighting(Brake light) ：Blue Line:Red lighting(Running light) ；2 *Yellow Line:Yellow(Turn Left/Right Light) ；YOU CAN TEXT IT BEFORE INSTALL！.
  • Fitment： Compatibility with/Replacement for HONDA MSX /Grom 125 2013 - 2016 , CB 650 F 2014 - 2015, HONDA CBR 650 F 2014-2015 , HONDA CTX 700 N 2013 - 2015.
  • for ‘17-18’ Compatibility with/Replacement for Honda Grom Please check your taillights bucket and the lisitng picture（4&5）,Some bikes may not the perfect fitment need to modify!!!.
  • Note！！LED light usually use little bit power, sometimes after you install, the LED light blink so fast or not blink, if you have this issue, you may need LOAD RESISTOR to put between the LED lights and POSITIVE, usually go around 6 ohm LOAD RESISTOR will,make it work, however we do not carry any load resistors,please purc....
Check Stock

Flasher Relay 3 Pin Adjustable LED Flasher Relay LED Flasher Blinker Turn Signal Light Blinker Universal for 12V 24V Automobiles and Motorcycles

  • 12V 24V Flasher Relay: This is a superfine quality LED flasher relay universal for 12V 24V automobiles and motorcycles.
  • Practical and Durable: The LED flasher blinker is helpful in solving problems related to turn signal LED light, such as rapid flashing, no flashing or....
  • Stable Performance: This LED flasher relay adopts advanced SMD technology, features short circuit automatic protection, overload automatic protection,....
  • Easy Installation: The turn signal light flasher with standard 3-PIN connector design, easy to install, plug and play.
  • Working Parameters: The size of this turn signal flasher is 5.3 x 3 x 2.6cm / 2.1 x 1.2 x 1 inches, and its applicable power is 0.1-150W.
Check Stock

Motogadget MG6002011/MG6002012 - m-Blaze Disc LED Bar End Turn Signal, Black, PAIR for 7/8' and 1' Bars

  • m-Blaze Disc Black Left and Right side LED bar end blinker for 7/8" or 1" handlebars.
  • Installation: rubber clamps for inner handlebar diameter of 14mm up to 21 mm are included.
  • This turn signal can be operated like any other LED turn signal with load resistors or all load independent flasher relays from motogadget (m-Flash, m-Wave, m-Stop, m-Relay+).
Check Stock

Yibid 12v 2-Pin Speed Adjustable LED Flasher Turn Signal light Electronic Relay fix Hyper Control Flash for Suzuki Motorcycle Honda Kawasaki Ninja Yamaha Dirt dual street sport ATV Bike, Orange Color

  • 2-pin Electronic LED Flasher is also speed adjustable. Allow LED bulbs to blink at the normal rate.
  • Can use a flat head screw driver to adjust the knob on the bottom to set its flashing speeds from 50c/m to 200c/m.
  • Directly replace the OEM two-pin flasher,Eliminate the need for tapping wires to install the load resistors,Works for most motorcycle/bike to fix the LED bulbs related turn signal light hyper flashing, not function properly issues..
  • Some bike not fit the old pole,may need you a out-wire connection to the lights ,pls kindly know that.
  • Work for most Motorcycles such as Honda, Kawasaki, KTM, Suzuki, Yamaha and on…...
Check Stock

2pcs LED Flasher Relay 2 Pin,12V Relay with Harness for Motorcycle LED Flash Turn Signal Control Relays

  • 【High Quality】ZSSElec 12 volt relay is made of durable high-quality materials (ABS plastic, sturdy copper wire, and metal),copper wires can....
  • 【Easy to Install】Just need to connect turn signal flasher relay 2 pins to the battery. No tools are required. (NOTE: if the wiring connectors are....
  • 【Flasher Relay for LED Turn Signal】ZSSElec electronic turn signal flasher relay help control the flash rate of the lights on your motorcycles,....
  • 【Motorcycle Flasher Relays】Automotive replacement flashers compatible for most bike scooter, motorcycle,such as such as Honda, Kawasaki, Suzuki,....
  • 【Packing】2pcs 12V 2pin LED flasher relay to meet your demands..
Check Stock

12V Speed Adjustable 2 Pin LED Electronic Flasher Relay for Motorcycle Turn Signal Direct Replacement Universal Hazard Warn Hyper Flash Relay Black,2pcs

  • 【SPEED ADJUSTABLE】This LED flasher relay fixes motorcycle turn signal hyper flash, allow LED light to blink at the normal rate, Clockwise:SLOWER ,....
  • 【APPLICATION】This 2-Pin Electronic Led Flasher Relay fit for most motorcycle/bike to fix the LED bulbs related turn signal light flashing, not....
  • 【SPECIFICATION】Blinker Relay 2 Pin. Operating Voltage: 12V (11V-15V). Max Power: 42W. Switch Power: 0.02A to 12A. Working Temperature: -40°C to....
  • 【PLUG AND PLAY】This Turn Signal Flasher Relay is plug-and-play. Work to directly replace Most Standard Factory 2-Pin Flasher. Eliminate the need....
  • 【PACKAGE INCLUDED】2PCS Black adjustable 2 Pin motorcycle flasher relay for LED turn signal..
Check Stock

Makita Brush Set (Makita 9565CV, 9564CV, PW5001C)

  • Powerful 13.0 AMP motor delivers more output and variable (2,800 - 10,500) RPM for the most demanding applications.
  • SJS technology is a mechanical clutch system that minimizes motor and gear damage.
  • Variable speed control dial enables user to match the speed to the application.
  • Electronic controller provides constant speed control which automatically applies additional power to the motor to maintain speed under load.
  • Electronic controller provides soft-start which is designed to suppress start-up reaction for smooth start-ups and longer gear life.
Check Stock

JDM ASTAR Super Bright 3030-15SMD 360 Beam White/Amber 7443 7444 Switchback LED Bulbs For Turn Signal Lights

  • Built with constant-current inductive circuitry, along with transient suppression.
  • The 50w 6ohm load resistor or flasher relay needed to prevent the hyper flash or the bulb does not blink..
Check Stock