Categories

Best Welding Table Top Clamps

Strong Hand Tools, Nomad, Steel Welding Table, Three 1.1″ (28mm) Tabletop Slots, Adjustable Angle & Height, Casters, Retractable Guide Rails, Eccentric Leveling Foot, TS3020, Black

  • Three 1. 1″ (28mm) slots in the tabletop allow for insertion of clamps to reach any point on the table..
  • Tabletop tilts to three positions: Horizontal, 30°, and folded for mobility..
  • Two retractable, perpendicular steel guide rails can be used as guides, stops, or clamping edges..
  • Affordable, convenient welding and work table for the welding shop or home shop.
  • Tabletop height can be adjusted from 26″ to 32″ (660 – 810 mm)..
  • Table moves about the work area on 2 sturdy casters..
Check Stock

WYNNsky Magnetic Welding Support Ground Clamp, 2pcs Set, Single and Double Welding Head, Copper Tail

  • Design: This magnetic clamp attaches easily to any smooth metal surface, flat or curved. It holds on tightly, without budging easily. Super suction magnet at the bottom, large suction power, long-lasting magnetism..
  • Application: This device serves as the ground point, which you can take with you anywhere. Simply tack this onto a convenient spot, hook up your safety wire and you're ready to weld..
  • Material: The welding magnet head adopts high quality material, durable and solid. Has brass tail has good welding stability, durable, anti-rust, has good performance and long service life..
  • Advantage: This magnetic clamp is handy to have in such situations. You can stick in on a car body and not have to damage the paint. The clamp can also be attached to metal poles, struts, railings or the welding table..
  • Including 1pc Single Head Magnetic Welding Ground Clamp.
  • 1pc Double Head Magnetic Welding Ground Clamp.
  • 1pc Copper Tail Welding Stability Clamps..
Check Stock

ABN Butt Welding Clamps - 8 Piece Small Welding Clamps Auto Body Panel Clamps for Edge to Edge Welding

  • [Perfectly Align Panels] Use the ABN Welding Square Clamp Set to pinch sheet metal panels level to each other.
  • While these metal clamps hold panels edge to edge with a 1mm gap, you can quickly weld the sheets together.
  • [Fits your Project] Each welding square tool pipe clamp can extend the clamp block to provide a .4-inch (1cm) tall gap.
  • Fits 3/16-inch to 26 gauge sheet metal materials.
  • [Easy to Use] Loosen the winged nut from the alignment screw then wedge two panels across from each other between the square body and the clamp block.
  • Tighten the winged nut to ensure a secure hold.
  • Use all 8 clamps for larger projects, then joint weld between them.
  • [Built to Last] Panel welding clamps are constructed of zinc-plated steel to ensure maximum durability and strength while resisting rust.
  • [Contents] Welding accessories set includes 8 welding corner square welder clamps.
  • Used to make precision butt welds and edge-to-edge welds for patch repairs in floors, wings, door skins, fabricating, and re-skinning projects.
Check Stock

Toolly 16 Pack Butt Welding Clamps - Small Welding Clamps Auto Body Panel Clamps for Edge to Edge Welding

  • Butt Welding Clamps includes 16 welding corner square welder clamps.
  • Used to make precision butt welds and edge-to-edge welds for patch repairs in floors, wings, door skins, fabricating, and re-skinning projects.
  • Use the Toolly Welding Square Clamp Set to pinch sheet metal panels level to each other.
  • While these metal clamps hold panels edge to edge with a 1mm gap, you can quickly weld the sheets together.
  • Each welding square tool pipe clamp can extend the clamp block to provide a .4-inch (1cm) tall gap.
  • Fits 3/16-inch to 26 gauge sheet metal materials.
  • Loosen the winged nut from the alignment screw then wedge two panels across from each other between the square body and the clamp block.
  • Tighten the winged nut to ensure a secure hold.
  • Use all 16 clamps for larger projects, then joint weld between them.
Check Stock

Tysun 4 Pcs 6 Inch C Clamp Set, Up to 6 Inch Jaw Opening, 2-5/8 Inch Throat Depth Heavy Duty C-Clamps for Woodworking Welding and Building

  • ★【Heavy Duty C Clamp Set】6 Inch c clamp made of high quality cast malleable iron, rust resistance and corrosion resistance, sturdy and durable.
  • black coated surface construction protects your clamps from moisture, preventing corrosion from damaging clamps..
  • ★【6 Inch C Clamp Size】Maximum jaw opening: 6 inches.
  • ★【Maximum Pressure】Sliding T-handle to produced maximum torque with little effort thereby reducing hand fatigue. Chrome-plated screw thread turns easily and does not bind so your clamps will last as long as you need them..
  • ★【Top Locking Force】Aside from being compact and made of high-quality steel for holding metal pieces together for welding, c clamps also allows for secure gripping to glue wood pieces together..
  • ★【Wide Application】Versatile c clamp secures parts for assembly, fastening, gluing, and welding in woodworking, metalworking, and automotive applications..
Check Stock

ATPEAM Butt Welding Clamp | Pack of 16 Small Welding Clamps Auto Body Panel Clamps for Edge to Edge Welding

  • Premium Material: Panel welding clamps are constructed of zinc-plated steel to ensure maximum durability and strength while resisting rust.
  • Fits your Project: Each welding square tool pipe clamp can extend the clamp block to provide a .4-inch (1cm) tall gap.
  • Fits 3/16-inch to 26 gauge sheet metal materials.
  • Good performance: These small welding clips can be completely fixed before butt welding, leaving only a small gap to make the weld completely penetrate. This is an ideal choice for professionals engaged in sheet metal body repair..
  • Easy to Use: Loosen the winged nut from the alignment screw then wedge two panels across from each other between the square body and the clamp block.
  • Tighten the winged nut to ensure a secure hold.
  • Use all 16 clamps for larger projects, then joint weld between them.
  • Package Included: Welding accessories set includes 16 welding corner square welder clamps.
  • Used to make precision butt welds and edge-to-edge welds for patch repairs in floors, wings, door skins, fabricating, and re-skinning projects.
Check Stock

OBPSFY 5 PCS Magnetic Welding Clamps Set,Adjustable V-Pads Fixture Clamp Hand Tools,Magnets On Both Pad Face and Bottom

  • 【Welding Clamp】* Hold tabs,pipe, gussets, plates and odd shaped pieces in position for tack welding.Light duty & tight spot holding! Build, Hold, and Position Steel.Magnetic tack welding Tool，make welding easier..
  • 【Strong Hand Tools】* Adjustable welding magnet, Magnetic welding holder, hold and position round, flat, and square parts in light duty substructure applications! Time saving magnetic tools for welding..
  • 【Material】* The magnetic welding clamps are made of high quality stainless steel, sturdy and durable, can be used for a long time.Magnets on both pad face and the bottom,Can hold the workpiece well for welding work..
  • 【Note】* Avoid Pronlonged exposure to high heat. The Magnets may demagnetize with temp. exceeding 185°F.（Heat Warning）.
  • 【Package】* 5 Pack Magnetic Welding Clamps（2" ，Pull Force 12 lbs.）.
Check Stock

FOITECHY 4 Pcs Magnetic Welding Clamps,Adjustable V Type Welding Clamps,Adjustable V-Type Fixture,Magnetic V Pads Kit, Magnetic V-sharp Tab Holder Corner for Tack Welding

  • 1.djustable V-Type Fixture Clamp: Magnetic welding clamps provide secure gripping power for rapid,hold and position round, flat, and square parts in light duty substructure applications.
  • 2.4 Pack strong hand magnet(XDV4: 2"),Pull Force 12 lbs. Our V-type magnetic welding clamps are made of high quality stainless steel, sturdy and durable, can be used for a long time.
  • 3.The V-type magnetic welding clamps are suitable for holding tabs, gussets, plates and odd shaped pieces in position for tack welding. They are widely used in doors, tool boxes, windows, wooden boxes, furniture, and other equipment..
  • 4.Heat Warning: Avoid Pronlonged exposure to high heat. Rare-earth Magnets may demagnetize with temp. exceeding 185°F.
Check Stock

Spurtar 6pcs Welding Magnet Welding Magnets and Clamps 75lbsX2+50lbsX2+25lbsX2 Magnetic Welding Holder 3 4 5 Arc Welding Electrode Holders 45 90 135 Degree Mig Welder Welding Accessories and Tools

  • STRONG POWER: 6 pieces different sizes welding magnet supports any ferrous metal object up to 25 lbs, 50 lbs, 75 lbs, satisfying all kinds of needs.
  • SAFE & SECURE: These welding magnets and clamps grip metal and hold it at the angle you need to work safely and efficiently. The welding holders are compact with durable high gloss enamel end plates.
  • THREE ANGLES: Heavy-duty arrow design steel welding magnet square supports material at 45°, 90°, and 135° for easy access. Can be used as double sided holder for welding, assembly and marking work.
  • MULTIPURPOSE: The magnetic welding holder clamps connects parts, freeing up your hands for efficient work and improve work safety, and it can also be used as a floater to separate steel plates.
  • EFFICIENCY: Spurtar Welding Magnet Set Magnetic Tool Holder s ideal welding tools and accessries for being used as holder and positioner in welding, soldering, marking off, pipe installation, making your welding job more efficiently and precisely..
Check Stock

4PCS C-Clamp Stainless Steel Clamps Heavy Duty Bracket for Woodworking Mount, with Wide Jaw Openings

  • Table Clamp Material: It is made of high-quality 304 stainless steel precision casting, the workpiece is compact and has no loose pinholes, rust and scratch resistance, and durable..
  • Clamps Widely Used：Wide range of uses: It is suitable for assembly, fastening, and welding in metal processing and automotive applications.with strong clamping force and easy to use..
  • C Clamp Easy to install: With adjustable positioning screws, it can be easily clamped on any plane, and the screws can be adjusted according to needs, which is convenient to use..
  • Clamps Design：The design of the c-shaped clamp can provide a comfortable use experience, Bandwidth port the design of the clamp can ensure that the clamped object will not be easily deformed, thereby ensuring a firm grip..
  • C Clamps Heavy Duty Size: The clamping range is 16-25mm/0.6-1 inches, there are 3 M8 threaded holes, and the opening is 30mm..
Check Stock

TRRAPLE Magnetic Welding Clamps, Adjustable V-Type Fixture Clamp, 2/4 Pcs Durable Stainless Steel Tab Holder Corner Butt Welding Panel Clamps Tools

  • HIGH QUALITY WELDING CLAMPS -- Our v-type magnetic welding clamps are made of made of high quality stainless steel, sturdy and durable, can be used for a long time..
  • MAGNETIC HOLDERS -- One rare earth magnets in each pad provide secure gripping power for rapid, and convenient, holding and positioning..
  • EASY TO USE -- Pads pivot to hold onto round, square, or flat metal surfaces, easy to install and apply..
  • PERFECT SPOT WELDING CLAMP -- Hold tabs, gussets, plates and odd shaped pieces in position for tack welding..
  • WIDELY APPLIED -- Widely used on doors, tool boxes, windows, wooden case, furniture and so on..
Check Stock

YESWELDER Magnetic Welding Clamps, Adjustable V-Type Fixture Clamp, Suspender Fixture Adjustable Pads Kit(4 Pcs)

  • HIGH QUALITY ▶V-type magnetic welding clamps, sturdy and durable, can be used for a long time.
  • EASY TO USE▶Hold and position round, flat, and square Parts in light duty substructure applications!Easy to install and apply.
  • MAGNETIC HOLDERS▶ Magnets on the pad face only.
  • INCLUDE▶ Each item contains 4 pcs of Magnetic Welding Clamps.
Check Stock

Dewalt Adjustable Height Portable Steel Welding Table and Work Bench 18 x 46-inch Tabletop Folding Legs Carrying Handle and Cord Minder

  • Steel construction - durable steel construction with an even distributed weight capacity of 1000-pounds.
  • Mounting options - strategically located slots / post holes for mounting and clamping any shape project.
  • Tabletop or stand-alone - useable folded up atop existing work table or as a 36-inch tall free-standing welding station.
  • Double locking legs - table legs have both spring pin / snap button locks and locking for added security under load.
  • Grounding stud - conveniently located ground stud for connecting grounding clamps and leads.
Check Stock