Categories

Best Wilwood Brake Kits

2" DROP SUSPENSION & WILWOOD 4 PISTON BRAKE SET FOR 55-57 CHEVY, CURRIE REAR END, AXLES, 9" FORD POSI-TRAC 3RD MEMBER, RED CALIPERS, 12" ROTORS SPINDLES MASTER CYLINDER BOOSTER CONTROL ARMS

  • Brand New Suspension & 12" Wilwood Brake Kit For 1955-1957 Chevys with 2" Drop Spindles (Part # GMB5557X-K72). This specific set features 2" drop spindles, Rotors, and Red Dynalite 4 piston front calipers & Red Dynalite 4 piston rear calipers. Fits: 1955-1957 Chevrolet Bel Air, Delray, 150, & 210. Excludes All Station Wagons, Sedan Deliveries, and Nomads due to their Bowtie shaped gas tank that requires a centered housing rear end, as opposed to a centered pinion rear end..
  • Includes: *Currie 9-Plus Notch-Back rear end with 31 spline axles (#CE-GMB5557X): Currie crate rear ends are designed to be a bolt-in upgrade. Built to the stock 60” width & pinion specs. Heavy-duty 2" wide leaf spring pads are installed in the stock location for easy bolt-in installation *Southwest Speed 9" Ford Rear End Third Member With Posi Trac-Loc (#603-2078): This kit comes with a 3.70 ratio gear, which is a good cruising ratio. We have ratios from 3.50 to 5.00 that can be substituted in.
  • *Southwest Speed 2" Drop Spindles (SWS Part # 103-9760): SWS drop spindles provide a full 2" drop, while not changing the vehicle's steering geome....
Check Stock

NEW WILWOOD GO KART BRAKE SET WITH CALIPER PADS MASTER CYLINDER & LINE KIT FOR 1/8 ROTORS GREAT FOR KARTING JR DRAGSTER ETC SOUTHWEST SPEED

  • Wilwood Karting Kit with Brake Caliper & Pads, Master Cylinder, 5' of Nylon Line, & 90 Degree Fitting to use with Caliper if necessary. (Wilwood Part #120-5498, #260-5520, #928-503, & #928-560)..
  • Wilwood Karting Kit with Brake Caliper & Pads, Master Cylinder, 5' of Nylon Line, & 90 Degree Fitting to use with Caliper if necessary. (Wilwood Part #120-5498, #260-5520, #928-503, & #928-560). Kit Includes: Wilwood Go-Kart Caliper for .125" Rotors Fits 0.125" Thick rotors Features Two 1.00" Pistons Weighs only 1.2 lbs. Comes with high friction brake pads..
  • Wilwood Go-Kart Master Cylinder with a 1/2" Bore 1/2" Bore Weighs only .55 lbs. This super lightweight aluminum master cylinder designed specifically for kart & jr. dragster racing applications incorporates an adjustable lever ratio with a remote mount clear fluid reservoir for easy monitoring The assembly comes ready to install and includes billet bracket, lock-wired drilled hardware, & fluid line fitting ..
  • 5 Feet of -3 Nylon Brake Line 3/16" Nylon tubing 5' Should equip most karts with some left-over..
  • 90 Degree Fitting for Caliper Depending on how everything is mounted, the line might run to the caliper at a bad angle for the straight fitting. This 90 degree fitting instal....
Check Stock

1955-57 Fits Chevy 2" Drop Spindles, Aftermarket Disc Brake Conversion Kit

  • Ideal for use with Wilwood or other aftermarket brake kits applicable to Heidt's Tri-5 drop spindle application.
  • 2" drop design to lower the front of you car and achieve the stance you are after.
  • Cannot be used with stock drums or brake conversion for stock type spindle.
  • Ball joints mount through the top, on both top & bottom ball joint mount bosses.
Check Stock

NEW WILWOOD LONG REVERSE SWING MOUNT CLUTCH OR BRAKE PEDAL ASSEMBLY WITH ADJUSTABLE PEDAL PADS, 6 TO 1 RATIO

  • Brand New Wilwood Long Reverse Swing Mount Clutch Pedal or Brake Pedal with Adjustable Pedal Pads (Wilwood Part # 340-13574)..
  • Wilwood's new Reverse Mount Swing Pedal assembly can be used as a clutch pedal with a single outlet master cylinder or as a brake pedal with a tandem master cylinder..
  • It features all aluminum frame and forged aluminum pedal arms with ladder style construction. ..
  • Features: | Can be used: | * As a Clutch Pedal with a single outlet master cylinder | * As a Brake Pedal with a tandem master cylinder that has a horizontal mounting, when used with a Wilwood Part # 250-3677 (not included with this pedal).
  • Lightweight | * All aluminum frame and forged aluminum pedal arms with ladder-style construction | * New waffle style pedal pads are of special adjustable design that allows fine-tuning of the pedal location and clearance | * Features a 6:1 pedal ratio | * Easy mounting location | * Below you can view and download the instruction booklet for this assembly here..
Check Stock

NEW CURRIE 70-87 CHEVY C-10 GMC C-15 C1500 TRUCK 2WD 5-LUG REAR END WITH WILWOOD DISC BRAKES, 11\ DRILLED ROTORS, RED CALIPERS, LINES, PARKING BRAKES, AXLES BEARINGS C10 C15, 1982 1983 1984 1985 1986

  • New Currie Enterprises Rear End with 31 Spline Axles with Wilwood Disc Brake Kit including Drilled Rotors and Red Calipers, Parking Brake Cable Kit, and Brake Line Kit for the applications below (Part # GMC7087X5-K7) 003e Currie Crate Rear Ends are designed to be a bolt-in upgrade.
  • Fits: | Chevrolet Trucks: 003e Will Fit All Late-1970 to 1987 C-10 2wd Trucks with 5-Lug wheels | GMC Trucks: 003e Will Fit All Late-1970 to 1987 C15/C1500 2wd Trucks with 5-Lug wheels.
  • Includes: | Currie 9-Plus Centurian Notch-Back Rear End with 31 Spline Axles (Currie # CE-GMC7087X5) 003e 31 Spline performance axle package 003e Housing includes all 3rd member studs installed 003e GMT7087X5 GMC7072X5 GMC7387X5 003e Built to the stock overall width (63 5/8") and pinion offset specs 003e 63 5/8" is measured outside-of-axle-flange to outside-of-axle-flange, in other words, where the wheel bolts on to where the wheel bolts on.
  • Wilwood 11" Disc Brake Kit with Drilled Rotors and Red Calipers (Wilwood Part # 140-11389-DR): | Brake Kit includes: 003e Drilled/Slotted, .810" Thick x 11.00" O.D. Rotors with Hats 003e Low-Profile 4 Piston Dynapro Calipers - Red 003e Drum Parking Brake Assemblies with Caliper Mounting Brackets 003e Bearing Retainers 003e BP-10 Smart Compound Br....
Check Stock

Motive Products - 0103 Brake System Power Bleeder for Chrysler/Dodge/Mopar

  • Motive Products Power Bleeder kits use pressurized brake fluid to force air and old fluid out of your brake lines.
  • Just pour clean fluid into the pressure tank, attach the Power Bleeder cap to your fluid reservoir, and pressurize the system using the built-in hand....
  • Features custom cap to fit most late model Chrysler and Dodge cars and trucks..
  • Also fits some after market reservoirs and master cylinders made by Strange Engineering and Wilwood that use two twist on caps..
  • Built-in heavy duty hand pump (no other pressure source is needed) and precision pressure gauge ensures safe and effective operation..
Check Stock

Performance Friction 7751.13.20.44 Brake Pads Wilwood Sl

  • PERFORMANCE FRICTION 13 AP/Outlaw/Wilwood SL Brake Pads 4 pc P/N 7751-13-20-44.
Check Stock

NEW SOUTHWEST SPEED RACING BRAKE & CLUTCH PEDAL ASSEMBLY WITH MASTER CYLINDERS & BALANCE BAR, REVERSE SWING MOUNT, SHORT 5 TO 1 RATIO

  • Brand New Southwest Speed Short Reverse Swing Mount Brake & Clutch Pedal Combo Kit With 3 Aluminum Master Cylinders (SWS Part # 301-2663). This combo is very similar to the Wilwood Part # 340-4828X3, only about $50 cheaper..
  • Southwest Speed High Volume Aluminum Master Cylinders | * High pressure die-cast from high-grade aluminum, fully machined and assembled with extreme precision * Features the highest fluid capacity of any integral reservoir design * With a total capacity of 8.2 ounces, there is at least 26% more fluid than most competitive brands * More fluid volume means cooler temperatures and additional insurance for extreme conditions where high pad wear can compromise fluid levels during long runs.
  • Kit includes: | * 1 - Reverse swing mount dual pedal, short design, 5:1 ratio (# 301-266) * 1 - Aluminum clutch master cylinder, 3/4" bore (# 301-290) * 1 - Aluminum brake master cylinder, 7/8" bore (# 301-291) * 1 - Aluminum brake master cylinder, 1" bore (# 301-292).
  • Find more Pedals as well as many other high performance auto parts by visiting the Southwest Speed Amazon Store..
  • Southwest Speed Dual Brake and Clutch Pedal | * This pedal assembly combines the brake and clutch pedals together in one unit and positions the master cylinders inside t....
Check Stock

WILWOOD HYDRAULIC HAND BRAKE LEVER & INTEGRAL MASTER CYLINDER,VT,DRIFT,RALLY CAR

  • Brand New Wilwood Hydraulic Vertical Handbrake Lever Assembly and Wilwood Compact Integral Girling-Style Master Cylinder (Wilwood Part #340-14769 & #260-15098)..
  • This set is designed to be used as a stand-alone system..
  • Lightweight forged aluminum 11:1 ratio "H" beam lever with ergonomic full-length grip.
  • Durable e-coat finish for long-lasting good looks and resistance to corrosion or oxidation.
Check Stock

iLSKW Golf Cart Ezgo Window Sash Windshield Retaining Clips for EZGO Club Car Yamaha Fit 1\x1\ Tube of Golf Carts

  • 2 Sets for two EZGO Brake Shoes 1 Set for one EZGO Brake Shoe Fit Model: EZGO Brake Shoes Spring Kits Fit EZGO TXT (1991-up) Gas or Electric vehicles with Bendix brakes. WILL NOT FIT RXV models..
  • Fit Model:Yamaha EZGO Brake Hardware Kit Fit Yamaha G14, G16, G19, and G22 Gas Or Electric 1994-2006..
  • Fit OEM Part Number: EZGO #27944G01.YAMAHA #JG5819G-00..
  • Advantage For Upgrade Golf Cart Brake Spring Kits :Repairs Your Brake Cluster For More Tension Between Your Drum And Shoes..
  • Package Include:2 Sets ezgo golf cart Bendix Brake Shoes Spring Kits Can Install 2 Brakes,For Both Drums on One Cart,Easy Installation..
Check Stock

MOSNAI EZGO Bendix Brake Shoes Spring Kits EZGO TXT Golf Carts 1991 up Gas/Electric Yamaha G14, G16, G19, G20, G21 and G22 Brake Hardware Kit JG5819G-00,27944-G01 (2 Sets)

  • Fit Model: EZGO Brake Shoes Spring Kits Fit EZGO TXT (1991-up) Gas or Electric vehicles with Bendix brakes. WILL NOT FIT RXV models..
  • Fit Model:Yamaha EZGO Brake Hardware Kit Fit Yamaha G14, G16, G19, and G22 Gas Or Electric 1994-2006..
  • Fit OEM Part Number: EZGO #27944G01.YAMAHA #JG5819G-00..
  • Advantage For Upgrade Golf Cart Brake Spring Kits :Repairs Your Brake Cluster For More Tension Between Your Drum And Shoes..
  • Package Include:2 Sets ezgo golf cart Bendix Brake Shoes Spring Kits Can Install 2 Brakes,For Both Drums on One Cart,Easy Installation..
Check Stock

BOSCH 50011227 QuietCast Premium Disc Brake Rotor - Compatible With Select Lexus ES300, ES330; Toyota Avalon, Camry, Solara; REAR; 1 PACK

  • [Applicable Models] - Automotive replacement brake rotors kits 120.63059,53022 fit for 2005-2018 for Chrysler 300,2009-2018 for Dodge Challenger,2006-2018 for Dodge Charger,2005-2008 for Dodge Magnum.
  • [Improve Performance] - The Quiet brake rotor is made of high-quality alloy casting, which can provide overall strength, unique slot design, achieve greater surface contact, improved noise attenuation and better heat capacity.
  • [Extended Service Life ] - LSAILON All rotors are silver zinc plated to keep the rotors looking good while achieve and extend the life of the rotor.
  • [Perfect Match Brake Kit] - Our Performance brakes rotors kits adhere to strict quality control standards to push brake friction to the limit and determine specific properties, including noise, overall friction Performance and wear characteristics.
  • [Important Information] - Please make sure that your part number and car model match the product kit before buying, make sure all brake components are properly installed and in good working order.
Check Stock

NEW SUSPENSION & WILWOOD BRAKE SET WITH CURRIE REAR END & AXLES, POSI-TRAC, 11\ DRILLED DISCS, RED CALIPERS, MASTER CYLINDER BOOSTER ARMS 1968 1969 1970 1971 1972 CHEVY CHEVELLE EL CAMINO CUTLASS GTO

  • Brand New Suspension and Brake Kit for 1968-1972 GM A-Body Cars (Part # GMA6872X-K34) | This specific set features Wilwood brakes with Drilled/Slotted Rotors and Red Calipers | Fits: Chevrolet 003e 1968-1972 Chevelle, El Camino, and Monte Carlo | Buick: 003e 1968-1972 Skylark, Gran Sport (GS), Station Wagon, and Sportwagon | GMC: 003e 1970-1972 Sprint | Oldsmobile: 003e 1968-1972 Cutlass, 4-4-2, Station Wagon, and Vista Cruiser | Pontiac: 003e 1968-1972 GTO, Grand Prix, Lemans, Station Wagon, and Tempest.
  • For 1967 year model cars: | This rear end can be used in some of the 1967's 003e On 1967's, you must examine the original rear end in the car to determine whether it has: 003e Early Style Spring Pad - A flat coil spring pad with a bolt and a plate that retain the spring, or 003e Late Style Spring Pad - A stamped dome style pad that the spring sits atop unretained 003e The 2 styles of pads cannot be interchanged - the pinion angle would be adversly affected.
Check Stock