Categories

Best Xlpe Cables

TEMCo 10 AWG/Gauge Solar Cable - Made in The USA 100 Feet Black (Variety of Lengths Available)

  • MADE IN THE USA - Bare copper conductor, Cross linked Polyethylene (XLPE) Insulation.
  • RoHS Compliant, UL 4703, 44, 854 rated - Temperature rating: -40°C Min, 90°C Max. 600 V 10 AWG.
  • UV and Sunlight Resistant. Direct Burial rated Applications include: Solar Panels, DC circuits, inverter wiring..
  • The solar cable offered in this listing is 10 AWG which is UL rated for 40A. Using large diameter cable will minimize power line loss in your solar panel system. Choose the size offered above that makes installation easy and simple saving time and money during installation..
  • Widely used for solar applications along with batteries, lamps, household appliances, electric heating appliances, meters, instruments, motor lead wire and digital fields.
Check Stock

HEATIT HIRD 30 feet 5 Watts Per Foot Roof & Gutter Snow De-Icing Cable

  • Tough XLPE as inner insulation and weather resistant PVC (high-low temperature) as out jacket. 100% screen rate with the Aluminum foil and tinned....
  • Both CSA and ETL approved. 6 ft 18/3 cold lead with plug . Pre-assembled, ready to install, no maintenance required. Easy instruction manual, clips....
  • Designed to prevent ice build up, known as ice dams, from forming on roofs and in gutters and downspouts. Protect your roof from damage and leaking,....
  • Used for Metal or plastic gutters/downspouts, Inclined roofs Roofs with noncombustible shingles (Ex.: asphalt shingles) that meet national building....
  • Testing the cable before the installation.Uncoil the heat cable completely so it does not touch, cross over or overlap on itself. Do not plug in the....
Check Stock

HEATIT JHSF 60-feet 120V Self Regulating Pre-assembled Pipe Heating Cable

  • JHSF doesn't work unless the ambient temperature is below 37F/3 degree C. Please test the cable in a cold environment..
  • Suitable for use on plastic and metal water pipes.( including inlet pipe,drain pipe, sewer , palm tree frost protection etc). Self regulating heating cable output will adjust automatically based on the ambient temperature at each point along the cable..
  • Pre-assembled, easy to install. Including grounded plug with light, built in thermostat(turn the cable 37F on 50F off) and instructions. 120 volt, 3 watts/ft at 50 degrees F. Protect pipes up to 2" in diameter. Can be used by straight, spiral and overlap..
  • ETL approved. 2 ft 18/3 cold lead with plug. The lowest installation temperature of this heating cable is -10 degree C. Tough XLPE as inner insulation and weather resistant PE (high-low temperature) as out jacket. Ingress Protection 65..
  • Testing the cable before the installation. Uncoil the cable, plug in the heating cable. Normally you can feel the slight warm on the heating cable in few minutes..
Check Stock

HEATIT JHSF 120-feet 120V Self Regulating Pre-assembled Pipe Heating Cable

  • JHSF doesn't work unless the ambient temperature is below 37F/3 degree C. Please test the cable in a cold environment..
  • Suitable for use on plastic and metal water pipes.( including inlet pipe,drain pipe, sewer , palm tree frost protection etc). Self regulating heating cable output will adjust automatically based on the ambient temperature at each point along the cable..
  • Pre-assembled, easy to install. Including grounded plug with light, built in thermostat(turn the cable 37F on 50F off) and instructions. 120 volt, 3 watts/ft at 50 degrees F. Protect pipes up to 2" in diameter. Can be used by straight, spiral and overlap..
  • ETL approved. 2 ft 18/3 cold lead with plug. The lowest installation temperature of this heating cable is -10 degree C. Tough XLPE as inner insulation and weather resistant PE (high-low temperature) as out jacket. Ingress Protection 65..
  • Testing the cable before the installation. Uncoil the cable, plug in the heating cable. Normally you can feel the slight warm on the heating cable in few minutes..
Check Stock

HEATIT HIRD 80 feet 5 Watts Per Foot Roof & Gutter Snow De-Icing Cable

  • Tough XLPE as inner insulation and weather resistant PVC (high-low temperature) as out jacket. 100% screen rate with the Aluminum foil and tinned copper braid. More safe and more healthy..
  • Both CSA and ETL approved. 6 ft 18/3 cold lead with plug . Pre-assembled, ready to install, no maintenance required. Easy instruction manual, clips and spacers are included..
  • Designed to prevent ice build up, known as ice dams, from forming on roofs and in gutters and downspouts. Protect your roof from damage and leaking, keep the water flowing in gutter & downspouts..
  • Used for Metal or plastic gutters/downspouts, Inclined roofs Roofs with noncombustible shingles (Ex.: asphalt shingles) that meet national building codes. Different lengths are available.
  • Suitable for most roof and gutter configurations..
  • Testing the cable before the installation.Uncoil the heat cable completely so it does not touch, cross over or overlap on itself. Do not plug in the cable until it has been completely uncoiled. Plug cable in, and in approximately 5 minutes, you should feel slightly warm to the touch. Then unplug the cable..
Check Stock

HEATIT HIRD 200 feet 5 Watts Per Foot Roof & Gutter Snow De-Icing Cable

  • Tough XLPE as inner insulation and weather resistant PVC (high-low temperature) as out jacket. 100% screen rate with the Aluminum foil and tinned copper braid. More safe and more healthy. Three year limited warranty- If you are not completely satisfied with HEATIT heating cable, please don’t hesitate to contact us in any time..
  • Both CSA and ETL approved. 6 ft 18/3 cold lead with plug . Pre-assembled, ready to install, no maintenance required. Easy instruction manual, clips and spacers are included..
  • Designed to prevent ice build up, known as ice dams, from forming on roofs and in gutters and downspouts. Protect your roof from damage and leaking, keep the water flowing in gutter & downspouts..
  • Used for Metal or plastic gutters/downspouts, Inclined roofs Roofs with noncombustible shingles (Ex.: asphalt shingles) that meet national building codes. Different lengths are available.
  • Suitable for most roof and gutter configurations..
  • Testing the cable before the installation.Uncoil the heat cable completely so it does not touch, cross over or overlap on itself. Do not plug in the cable until it has been completely uncoiled. Plug cable in, and in approximately 5 minutes, you should feel slightly warm to the touch. Then unplug the cable..
Check Stock

Heat it HIRD 20 feet Roof Gutter De-Icing Cable

  • ...coiled. Plug cable in, and in approximately few minutes, it should feel slightly warm to the touch. Then unplug the cable..
  • Both CSA and ETL approved. 6 ft 18/3 cold lead with plug.
  • 5 watts/ft. Pre-assembled, ready to install, no maintenance required.
  • Easy instruction manual, clips and spacers are included..
  • Tough XLPE as inner insulation and weather resistant PVC (high-low temperature) as out jacket. 100% screen rate with the Aluminum foil and tinned copper braid. More safe and more healthy. Three year limited warranty- If you are not completely satisfied with HEATIT heating cable, please don’t hesitate to contact us in any time..
Check Stock

HEATIT HISD 18-feet Pipe Heating Cable with Built-in Thermostat

  • ...th light, built in thermostat, and instructions. Easy to install and use. 120 volt, 7 watts/ft. Built in thermostat to turn the cable 37F on 50F off. Energy saving. 100% screen rate with the Aluminum foil and tinned copper braid..
  • Both CSA and ETL approved. Industrial grade heat shrinkage tube for connection. Tough XLPE as inner insulation and weather resistant PVC (high-low temperature) as out jacket..
  • Maximum 1/2 in fiberglass insulation was used over the heating cable for lower temperature protection. Pipes must be at least 3 feet and at least 3/8” and less than 1 1/2” in. diameter. No crossing. No spiral. No overlap itself. Only straight..
  • Testing the cable before the installation. Uncoil the cable, plug in the heating cable and then put the thermostat part of the cable into an ice bucket for few minutes. When the temperature is below 37F, the thermostat will energize the cable to work. Normally you can feel the slight warm on the heating cable in few minutes. To avoid the overheat, please don’t plug in the cable for a long time for testing. When you feel the slight warm, please turn it off..
Check Stock

HEATIT HISD 15-feet Pipe Heating Cable with Built-in Thermostat

  • ...th light, built in thermostat, and instructions. Easy to install and use. 120 volt, 7 watts/ft. Built in thermostat to turn the cable 37F on 50F off. Energy saving. 100% screen rate with the Aluminum foil and tinned copper braid..
  • Both CSA and ETL approved. Industrial grade heat shrinkage tube for connection. Tough XLPE as inner insulation and weather resistant PVC (high-low temperature) as out jacket..
  • Maximum 1/2 in fiberglass insulation was used over the heating cable for lower temperature protection. Pipes must be at least 3 feet and at least 3/8” and less than 1 1/2” in. diameter. No crossing. No spiral. No overlap itself. Only straight..
  • Testing the cable before the installation. Uncoil the cable, plug in the heating cable and then put the thermostat part of the cable into an ice bucket for few minutes. When the temperature is below 37F, the thermostat will energize the cable to work. Normally you can feel the slight warm on the heating cable in few minutes. To avoid the overheat, please don’t plug in the cable for a long time for testing. When you feel the slight warm, please turn it off..
Check Stock

HEATIT HISD 12-feet Pipe Heating with Built-in Thermostat, Black

  • ...uctions. Easy to install and use. 120 volt, 7 watts/ft. Built in thermostat to turn the cable 37F on 50F off. Only use 5 amps or less of electricity. Energy saving. 100% screen rate with the Aluminum foil and tinned copper braid..
  • Both CSA and ETL approved. Industrial grade heat shrinkage tube for connection. Tough XLPE as inner insulation and weather resistant PVC (high-low temperature) as out jacket..
  • Maximum 1/2 in fiberglass insulation was used over the heating cable for lower temperature protection. Pipes must be at least 3 feet and at least 3/8” and less than 1 1/2” in. diameter. No crossing. No spiral. No overlap itself. Only straight..
  • Testing the cable before the installation. Uncoil the cable, plug in the heating cable and then put the thermostat part of the cable into an ice bucket for few minutes. When the temperature is below 37F, the thermostat will energize the cable to work. Normally you can feel the slight warm on the heating cable in few minutes. To avoid the overheat, please don’t plug in the cable for a long time for testing. When you feel the slight warm, please turn it off..
Check Stock

HEATIT HISD 3-feet Pipe Heating with Built-in Thermostat, Black

  • ...uctions. Easy to install and use. 120 volt, 7 watts/ft. Built in thermostat to turn the cable 37F on 50F off. Only use 5 amps or less of electricity. Energy saving. 100% screen rate with the Aluminum foil and tinned copper braid..
  • Both CSA and ETL approved. Industrial grade heat shrinkage tube for connection. Tough XLPE as inner insulation and weather resistant PVC (high-low temperature) as out jacket..
  • Maximum 1/2 in fiberglass insulation was used over the heating cable for lower temperature protection. Pipes must be at least 3 feet and at least 3/8” and less than 1 1/2” in. diameter. No crossing. No spiral. No overlap itself. Only straight..
  • Testing the cable before the installation. Uncoil the cable, plug in the heating cable and then put the thermostat part of the cable into an ice bucket for few minutes. When the temperature is below 37F, the thermostat will energize the cable to work. Normally you can feel the slight warm on the heating cable in few minutes. To avoid the overheat, please don’t plug in the cable for a long time for testing. When you feel the slight warm, please turn it off..
Check Stock

HEATIT JHSF 12-feet 120V Self Regulating Pre-assembled Pipe Heating Cable

  • ...meter. For a better freeze protection, at least 1/2 inch thick insulation material is recommended, especially for extremely cold weather..
  • ETL approved. 2 ft 18/3 cold lead with plug. Industrial grade heat shrinkage tube for connection.The lowest installation temperature of this heating cable is -10 degree C. Tough XLPE as inner insulation and weather resistant PE (high-low temperature) as out jacket. Ingress Protection 65. Durable.
  • Testing the cable before the installation. Uncoil the cable, plug in the heating cable and then put the thermostat part of the cable into an ice bucket for few minutes. When the temperature is below 37F, the thermostat will energize the cable to work. Normally you can feel the slight warm on the heating cable in few minutes. Four year limited warranty. If you are not completely satisfied with HEATIT heating cable, please feel free to contact us in any time, we’ll try our best to solve your issue.
Check Stock

HEATIT JHSF 6-feet 120V Self Regulating Pre-assembled Pipe Heating Cable

  • ...meter. For a better freeze protection, at least 1/2 inch thick insulation material is recommended, especially for extremely cold weather..
  • ETL approved. 2 ft 18/3 cold lead with plug. Industrial grade heat shrinkage tube for connection.The lowest installation temperature of this heating cable is -10 degree C. Tough XLPE as inner insulation and weather resistant PE (high-low temperature) as out jacket. Ingress Protection 65. Durable.
  • Testing the cable before the installation. Uncoil the cable, plug in the heating cable and then put the thermostat part of the cable into an ice bucket for few minutes. When the temperature is below 37F, the thermostat will energize the cable to work. Normally you can feel the slight warm on the heating cable in few minutes. Four year limited warranty. If you are not completely satisfied with HEATIT heating cable, please feel free to contact us in any time, we’ll try our best to solve your issue.
Check Stock